參數資料
型號: LPC2929FBD144
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: ARM9 microcontroller with CAN, LIN, and USB
中文描述: 32-BIT, FLASH, 125 MHz, RISC MICROCONTROLLER, PQFP144
封裝: 20 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT486-1, LQFP-144
文件頁數: 34/95頁
文件大?。?/td> 1855K
代理商: LPC2929FBD144
LPC2926_27_29
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 5 — 28 September 2010
34 of 95
NXP Semiconductors
LPC2926/2927/2929
ARM9 microcontroller with CAN, LIN, and USB
Programmable choice of interface operation: Motorola SPI or Texas Instruments
Synchronous Serial Interfaces.
Programmable data-frame size from 4 to 16 bits.
Independent masking of transmit FIFO, receive FIFO and receive overrun interrupts.
Serial clock-rate master mode: fserial_clk
f
clk(SPI)
/2.
Serial clock-rate slave mode: fserial_clk = f
clk(SPI)
/4.
Internal loopback test mode.
The SPI module can operate in:
Master mode:
Normal transmission mode
Sequential slave mode
Slave mode
6.13.5.1
Functional description
The SPI module is a master or slave interface for synchronous serial communication with
peripheral devices that have either Motorola SPI or Texas Instruments Synchronous
Serial Interfaces.
The SPI module performs serial-to-parallel conversion on data received from a peripheral
device. The transmit and receive paths are buffered with FIFO memories (16 bits wide
×
32 words deep). Serial data is transmitted on pins SDOx and received on pins SDIx.
The SPI module includes a programmable bit-rate clock divider and prescaler to generate
the SPI serial clock from the input clock CLK_SPIx.
The SPI module’s operating mode, frame format, and word size are programmed through
the SLVn_SETTINGS registers.
A single combined interrupt request SPI_INTREQ output is asserted if any of the
interrupts are asserted and unmasked.
Depending on the operating mode selected, the SPI SCS outputs operate as an
active-HIGH frame synchronization output for Texas Instruments synchronous serial
frame format or an active-LOW chip select for SPI.
Each data frame is between four and 16 bits long, depending on the size of words
programmed, and is transmitted starting with the MSB.
6.13.5.2
Pin description
The SPI pins are combined with other functions on the port pins of the
LPC2926/2927/2929, see
Section 6.12.3
.
Table 18
shows the SPI pins (x runs from 0 to 2;
y runs from 0 to 3).
Table 18.
Symbol
SPIx SCSy
SPI pins
Pin name
SCSy
Direction
IN/OUT
Description
SPIx chip select
[1][2]
相關PDF資料
PDF描述
LPC2930FBD208 ARM9 flashless microcontroller with CAN, LIN, and USB
LPC2939FBD208 ARM9 microcontroller with CAN, LIN, and USB
LPC3180FEL320 16-32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface
LPC3220FET296 ARM926EJ-S with 128 kB SRAM, USB High-speed OTG, SD-MMC, NAND flash controller
LPC3230FET296 ARM926EJ-S with 256 kB SRAM, USB High-speed OTG, SD-MMC, NAND flash controller, LCD controller
相關代理商/技術參數
參數描述
LPC2929FBD144,551 功能描述:ARM微控制器 - MCU ARM968 768K FL/16K RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2929FBD144551 制造商:NXP Semiconductors 功能描述:MCU ARM9 144LQFP
LPC2929FBD144-S 功能描述:ARM微控制器 - MCU ARM968 768K FL/16K EE/USB/CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2930 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 flashless microcontroller with CAN, LIN, and USB
LPC2930FBD208 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 flashless microcontroller with CAN, LIN, and USB