- 您現在的位置：買賣IC網 > PDF目錄385497 > LPC2378FBD144 (NXP Semiconductors N.V.) Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC PDF資料下載
參數資料
| 型號： | LPC2378FBD144 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 數學處理器 |
| 英文描述： | Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC |
| 封裝： | LPC2377FBD144<SOT486-1 (LQFP144)|<<http://www.nxp.com/packages/SOT486-1.html<1<Always Pb-free,;LPC2378FBD144<SOT486-1 (LQFP144)|<<http://www.nxp.com/packages/SOT486-1.htm |
| 文件頁數： | 32/68頁 |
| 文件大小： | 1443K |
| 代理商： | LPC2378FBD144 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
LPC2377_78
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 5 — 17 June 2010
32 of 68
NXP Semiconductors
LPC2377/78
Single-chip 16-bit/32-bit microcontrollers
7.25.1.2
Main oscillator
The main oscillator can be used as the clock source for the CPU, with or without using the
PLL. The main oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can
be boosted to a higher frequency, up to the maximum CPU operating frequency, by the
PLL. The clock selected as the PLL input is PLLCLKIN. The ARM processor clock
frequency is referred to as CCLK elsewhere in this document. The frequencies of
PLLCLKIN and CCLK are the same value unless the PLL is active and connected. The
clock frequency for each peripheral can be selected individually and is referred to as
PCLK. Refer to
Section 7.25.2
for additional information.
7.25.1.3
RTC oscillator
The RTC oscillator can be used as the clock source for the RTC and/or the WDT. Also, the
RTC oscillator can be used to drive the PLL and the CPU.
7.25.2
PLL
The PLL accepts an input clock frequency in the range of 32 kHz to 25 MHz. The input
frequency is multiplied up to a high frequency, then divided down to provide the actual
clock used by the CPU and the USB block.
The PLL input, in the range of 32 kHz to 25 MHz, may initially be divided down by a value
‘N’, which may be in the range of 1 to 256. This input division provides a wide range of
output frequencies from the same input frequency.
Following the PLL input divider is the PLL multiplier. This can multiply the input divider
output through the use of a Current Controlled Oscillator (CCO) by a value ‘M’, in the
range of 1 through 32768. The resulting frequency must be in the range of 275 MHz to
550 MHz. The multiplier works by dividing the CCO output by the value of M, then using a
phase-frequency detector to compare the divided CCO output to the multiplier input. The
error value is used to adjust the CCO frequency.
The PLL is turned off and bypassed following a chip Reset and by entering Power-down
mode. PLL is enabled by software only. The program must configure and activate the PLL,
wait for the PLL to lock, then connect to the PLL as a clock source.
7.25.3
Wake-up timer
The LPC2377/78 begin operation at power-up and when awakened from Power-down and
Deep power-down modes by using the 4 MHz IRC oscillator as the clock source. This
allows chip operation to resume quickly. If the main oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
When the main oscillator is initially activated, the wake-up timer allows software to ensure
that the main oscillator is fully functional before the processor uses it as a clock source
and starts to execute instructions. This is important at power on, all types of Reset, and
whenever any of the aforementioned functions are turned off for any reason. Since the
oscillator and other functions are turned off during Power-down and Deep power-down
modes, any wake-up of the processor from Power-down mode makes use of the wake-up
Timer.
The Wake-up Timer monitors the crystal oscillator to check whether it is safe to begin
code execution. When power is applied to the chip, or when some event caused the chip
to exit Power-down mode, some time is required for the oscillator to produce a signal of
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2387FBD100 | Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC |
| LPC2388FBD144 | Single-chip 16-bit-32-bit micro; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC |
| LPC2420FBD208 | Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface |
| LPC2420FET208 | Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface |
| LPC2460FBD208 | Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2378FBD144,551 | 功能描述:ARM微控制器 - MCU ARM7 512KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2378FBD144/CP32 | 制造商:NXP Semiconductors 功能描述:- Trays |
| LPC2378FBD144/CP3E | 制造商:NXP Semiconductors 功能描述: |
| LPC2378FBD144551 | 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU ARM7 72MHZ LQFP-144 |
| LPC2378-STK | 功能描述:開發板和工具包 - ARM DEV BRD FOR LPC2378 512KB FLASH 16KB RAM RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。