參數資料
型號: LPC2378
廠商: NXP Semiconductors N.V.
英文描述: Single-chip 16-bit/32-bit microcontrollers; 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
中文描述: 單芯片16-bit/32-bit微控制器,512的ISP /國際檢察官聯合會,以太網,USB 2.0,CAN和10 kB閃存位的ADC / DAC
文件頁數: 24/54頁
文件大?。?/td> 203K
代理商: LPC2378
LPC2378_1
NXP B.V. 2006. All rights reserved.
Preliminary data sheet
Rev. 01 — 6 December 2006
24 of 54
NXP Semiconductors
LPC2378
Fast communication chip
7.15 UARTs
The LPC2378 contains four UARTs. In addition to standard transmit and receive data
lines, UART1 also provides a full modem control handshake interface.
The UARTs include a fractional baud rate generator. Standard baud rates such as 115200
can be achieved with any crystal frequency above 2 MHz.
7.15.1
Features
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
UART1 equipped with standard modem interface signals. This module also provides
full support for hardware flow control (auto-CTS/RTS).
UART3 includes an IrDA mode to support infrared communication.
7.16 SPI serial I/O controller
The LPC2378 contains one SPI controller. SPI is a full duplex serial interface designed to
handle multiple masters and slaves connected to a given bus. Only a single master and a
single slave can communicate on the interface during a given data transfer. During a data
transfer the master always sends 8 bits to 16 bits of data to the slave, and the slave
always sends 8 bits to 16 bits of data to the master.
7.16.1
Features
Compliant with SPI specification
Synchronous, Serial, Full Duplex Communication
Combined SPI master and slave
Maximum data bit rate of one eighth of the input clock rate
8 bits to 16 bits per transfer
7.17 SSP serial I/O controller
The LPC2378 contains two SSP controllers. The SSP controller is capable of operation on
a SPI, 4-wire SSI, or Microwire bus. It can interact with multiple masters and slaves on the
bus. Only a single master and a single slave can communicate on the bus during a given
data transfer. The SSP supports full duplex transfers, with frames of 4 bits to 16 bits of
data flowing from the master to the slave and from the slave to the master. In practice,
often only one of these data flows carries meaningful data.
7.17.1
Features
Compatible with Motorola SPI, 4-wire TI SSI, and National Semiconductor Microwire
buses
相關PDF資料
PDF描述
LPC2388 Single-chip 16-bit/32-bit microcontroller; 512 kB flash with ISP/IAP, Ethernet, USB 2.0 device/host/OTG, CAN, and 10-bit ADC/DAC
LPC2460 Flashless 16-bit/32-bit micro; Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface
LPC2880 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface
LPC2880FET180 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface
LPC2888 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface
相關代理商/技術參數
參數描述
LPC2378FBD144 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 10/100 USB CAN 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7, 10/100, USB, CAN
LPC2378FBD144,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2378FBD144/CP32 制造商:NXP Semiconductors 功能描述:- Trays
LPC2378FBD144/CP3E 制造商:NXP Semiconductors 功能描述:
LPC2378FBD144551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU ARM7 72MHZ LQFP-144