參數資料
型號: LPC2106FHN48/01,55
廠商: NXP Semiconductors
文件頁數: 8/41頁
文件大?。?/td> 0K
描述: IC ARM7 MCU FLASH 128K 48-HVQFN
標準包裝: 260
系列: LPC2100
核心處理器: ARM7
芯體尺寸: 16/32-位
速度: 60MHz
連通性: I²C,Microwire,SPI,SSI,SSP,UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 32
程序存儲器容量: 128KB(128K x 8)
程序存儲器類型: 閃存
RAM 容量: 64K x 8
電壓 - 電源 (Vcc/Vdd): 1.65 V ~ 3.6 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 48-VFQFN 裸露焊盤
包裝: 管件
產品目錄頁面: 704 (CN2011-ZH PDF)
配用: 568-4310-ND - EVAL BOARD LPC2158 W/LCD
568-4297-ND - BOARD EVAL LPC21XX MCB2100
622-1019-ND - BOARD FOR LPC2106 48-LQFP
622-1008-ND - BOARD FOR LPC9103 10-HVSON
622-1005-ND - USB IN-CIRCUIT PROG ARM7 LPC2K
568-1756-ND - BOARD EVAL FOR LPC210X ARM MCU
其它名稱: 568-4368
935286613551
LPC2106FHN48/01-S
LPC2104_2105_2106_7
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 07 — 20 June 2008
16 of 41
NXP Semiconductors
LPC2104/2105/2106
Single-chip 32-bit microcontrollers
6.9 General purpose parallel I/O
Device pins that are not connected to a specic peripheral function are controlled by the
GPIO registers. Pins may be dynamically congured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
6.9.1 Features
Direction control of individual bits.
Separate control of output set and clear.
All I/O default to inputs after reset.
6.9.2 Features added with the Fast GPIO set of registers available on
LPC2104/2105/2106/01 only
Fast GPIO registers are relocated to the ARM local bus for the fastest possible I/O
timing, enabling port pin toggling up to 3.5 times faster than earlier LPC2000 devices.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All Fast GPIO registers are byte addressable.
Entire port value can be written in one instruction.
Ports are accessible via either the legacy group of registers (GPIOs) or the group of
registers providing accelerated port access (Fast GPIOs).
6.10 UARTs
The LPC2104/2105/2106 each contain two UARTs. One UART provides a full modem
control handshake interface, the other provides only transmit and receive data lines.
6.10.1 Features
16 byte Receive and Transmit FIFOs
Register locations conform to 16C550 industry standard
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B
Built-in baud rate generator
25:24
P0.28
0
GPIO Port 0.28
0
1
TMS
27:26
P0.29
0
GPIO Port 0.29
0
1
TCK
29:28
P0.30
0
GPIO Port 0.30
0
1
TDI
31:30
P0.31
0
GPIO Port 0.31
0
1
TDO
Table 7.
Pin function select register 1 (PINSEL1 - 0xE002 C004) …continued
PINSEL1
Pin name
Value
Function
Value after
reset
相關PDF資料
PDF描述
VI-213-CV-B1 CONVERTER MOD DC/DC 24V 150W
VE-23J-CV-B1 CONVERTER MOD DC/DC 36V 150W
VE-23H-CV-B1 CONVERTER MOD DC/DC 52V 150W
VE-230-CV-B1 CONVERTER MOD DC/DC 5V 150W
VE-2WV-CV-B1 CONVERTER MOD DC/DC 5.8V 150W
相關代理商/技術參數
參數描述
LPC2109 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit microcontrollers; 64/128/256 kB ISP/IAP flash with 10-bit ADC and CAN
LPC2109_11 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit microcontrollers; 64/128/256 kB ISP/IAP flash with 10-bit ADC and CAN
LPC2109FBD01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit microcontrollers; 64/128/256 kB ISP/IAP flash with 10-bit ADC and CAN
LPC2109FBD64 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 64K FLASH LQFP64 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 64K FLASH, LQFP64
LPC2109FBD64/00 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit microcontrollers; 64/128/256 kB ISP/IAP flash with 10-bit ADC and CAN