- 您現在的位置：買賣IC網 > PDF目錄1932 > LPC11U14FET48/201, (NXP Semiconductors)IC MCU 32BIT 32K 48TFBGA PDF資料下載
參數資料
| 型號： | LPC11U14FET48/201, |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 18/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 32BIT 32K 48TFBGA |
| 產品培訓模塊： | Code Density for LPC11xx |
| 標準包裝： | 490 |
| 系列： | LPC11Uxx |
| 核心處理器： | ARM? Cortex?-M0 |
| 芯體尺寸： | 32-位 |
| 速度： | 50MHz |
| 連通性： | I²C，Microwire，智能卡，SPI，SSP，UART/USART，USB |
| 外圍設備： | 欠壓檢測/復位，POR，WDT |
| 輸入/輸出數： | 40 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 6K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 3.6 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 48-TFBGA |
| 包裝： | 托盤 |
| 其它名稱： | 568-8578 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
LPC11U1X
All information provided in this document is subject to legal disclaimers.
NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet
Rev. 2.2 — 11 March 2014
25 of 72
NXP Semiconductors
LPC11U1x
32-bit ARM Cortex-M0 microcontroller
7.16.1.2
System oscillator
The system oscillator can be used as the clock source for the CPU, with or without using
the PLL. On the LPC11U1x, the system oscillator must be used to provide the clock
source to USB.
The system oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the
system PLL.
7.16.1.3
Watchdog oscillator
The watchdog oscillator can be used as a clock source that directly drives the CPU, the
watchdog timer, or the CLKOUT pin. The watchdog oscillator nominal frequency is
programmable between 7.8 kHz and 1.7 MHz. The frequency spread over processing and
temperature is
40 % (see also Table 13).
7.16.2 System PLL and USB PLL
The LPC11U1x contain a system PLL and a dedicated PLL for generating the 48 MHz
USB clock. The system and USB PLLs are identical.
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within
its frequency range while the PLL is providing the desired output frequency. The output
divider may be set to divide by 2, 4, 8, or 16 to produce the output clock. The PLL output
frequency must be lower than 100 MHz. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to lock, and then connect to the PLL as a clock source.
The PLL settling time is 100
s.
7.16.3 Clock output
The LPC11U1x features a clock output function that routes the IRC oscillator, the system
oscillator, the watchdog oscillator, or the main clock to an output pin.
7.16.4 Wake-up process
The LPC11U1x begin operation at power-up and when awakened from Deep power-down
mode by using the 12 MHz IRC oscillator as the clock source. This allows chip operation
to resume quickly. If the main oscillator or the PLL is needed by the application, software
will need to enable these features and wait for them to stabilize before they are used as a
clock source.
7.16.5 Power control
The LPC11U1x support a variety of power control features. There are four special modes
of processor power reduction: Sleep mode, Deep-sleep mode, Power-down mode, and
Deep power-down mode. The CPU clock rate may also be controlled as needed by
changing clock sources, reconfiguring PLL values, and/or altering the CPU clock divider
value. This allows a trade-off of power versus processing speed based on application
requirements. In addition, a register is provided for shutting down the clocks to individual
相關PDF資料 |
PDF描述 |
|---|---|
| LPC11U24FBD64/401 | IC MCU USB 64LQFP |
| LPC1227FBD64/301,1 | MCU 32BIT 128K FLASH 8K 64-LQFP |
| LPC12D27FBD100/301 | MCU 32BIT ARM CORTEX-M0 100-LQFP |
| LPC1315FBD48,551 | IC MCU 32BIT 32KB FLASH 48LQFP |
| LPC1343FBD48,151 | IC MCU 32BIT 32KB FLASH 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC11U14FHI33.201 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32-bit ARM Cortex-M0 microcontroller; up to 32 kB flash; 6 kB SRAM; USB device; USART |
| LPC11U14FHI33/201 | 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM CORTEX M0 32HVQFN |
| LPC11U14FHI33/201, | 功能描述:ARM微控制器 - MCU 32-bit ARM Cortex-M0 MCU RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC11U14FHN201 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32-bit ARM Cortex-M0 microcontroller; up to 32 kB flash; 6 kB SRAM; USB device; USART |
| LPC11U14FHN33 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-cost Cortex-M0 USB solutions with Smart Card interface |
發布緊急采購，3分鐘左右您將得到回復。