參數資料
型號： LPC11C12FBD48
廠商： NXP Semiconductors N.V.
元件分類： 32位微控制器
英文描述： Cortex-M0 with 16 kB flash, 8 kB SRAM, CAN and CANopen drivers on-chip
中文描述： Cortex-M0,16KB閃存，8 KB靜態隨機存儲器，CAN和CANopen片上驅動
封裝： LPC11C12FBD48/301<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html<1<Always Pb-free,;
文件頁數： 14/62頁
文件大小： 487K
代理商： LPC11C12FBD48
LPC11CX2_CX4
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3 — 27 June 2011
14 of 62
NXP Semiconductors
LPC11Cx2/Cx4
32-bit ARM Cortex-M0 microcontroller
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to full V
DD
level); IA = inactive,
no pull-up/down enabled.
[2]
See
Figure 26
for reset pad configuration. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to
reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down
mode.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see
Figure 25
).
[4]
I
2
C-bus pads compliant with the I
2
C-bus specification for I
2
C standard mode and I
2
C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see
Figure 25
).
[6]
5 V tolerant digital I/O pad without pull-up/pull-down resistors.
[7]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
GND
V
DD
21
8; 44
-
-
-
I
-
-
Ground for CAN transceiver.
Supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
Input to the oscillator circuit and internal clock generator circuits.
Input voltage must not exceed 1.8 V.
Output from the oscillator amplifier.
Ground.
XTALIN
6
[7]
-
I
-
XTALOUT
V
SS
7
[7]
5; 41
-
-
O
I
-
-
Table 4.
Symbol
LPC11C22/C24 pin description table
Pin
Start
logic
inputs
Type
Reset
state
[1]
Description
相關PDF資料
PDF描述
LPC11D14FBD100 32-bit ARM Cortex-M0 microcontroller; 32 kB flash and 8 kB SRAM; 4 x 40 segment LCD driver
LPC11U12FBD48 32-bit ARM Cortex-M0 microcontroller; up to 16 kB flash; 6 kB SRAM; USB device; USART; 2 SSPs
LPCXpresso
LPD-1 Phase Detectors 1000mV DC output , + 7dBmRF
LPDA-8003 LPDA-8003 Log Periodic Dipole Antenna
相關代理商/技術參數
參數描述
LPC11C12FBD48/301 功能描述:ARM微控制器 - MCU 32-bit Cortex M0 16KB 8K RAM CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC11C12FBD48/301, 功能描述:ARM微控制器 - MCU 32b 16K Flash 40I/O RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC11C12FBD48/301,15 制造商:NXP Semiconductors 功能描述:Bulk
LPC11C12FBD48-301 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32-bit ARM Cortex-M0 microcontroller; 16/32 kB flash, 8 kB SRAM; C_CAN
LPC11C14FB301 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32-bit ARM Cortex-M0 microcontroller; 16/32 kB flash, 8 kB SRAM C_CAN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*