- 您現在的位置：買賣IC網 > PDF目錄369797 > LM81CIMTX-3 Single-Ended Data Acquisition System PDF資料下載
參數資料
| 型號： | LM81CIMTX-3 |
| 英文描述： | Single-Ended Data Acquisition System |
| 中文描述： | 單端數據采集系統 |
| 文件頁數： | 14/33頁 |
| 文件大小： | 414K |
| 代理商： | LM81CIMTX-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Functional Description
(Continued)
3.0 USING THE LM81
3.1 Power On
When power is first applied, the LM81 performs a “power on
reset” on several of its registers. The power on condition of
the LM81’s registers in shown in Table 1 Registers whose
power on values are not shown have power on conditions
that are indeterminate (this includes the value RAM
,exclusive of the DAC data, and WATCHDOG limits). When
power is first applied the ADC is inactive. In most
applications, usually the first action after power on is usually
to write WATCHDOG limits into the Value RAM. Register
values can be returned to their default values after power is
applied to the LM81 by taking RESET low for at least 50 ns.
3.2 Resets
Configuration Register INITIALIZATION accomplishes the
same function as power on reset on most registers. The
Value
RAM
conversion
results,
WATCHDOG limits are not Reset and will be indeterminate
immediately after power on. If the Value RAM contains valid
conversion results and/or Value RAM WATCHDOG limits
have been previously set, they will not be affected by a
Configuration Register INITIALIZATION. Power on reset, or
Configuration Register INITIALIZATION, clear or initialize
the following registers (the initialized values are shown on
Table 1
Configuration Register
Interrupt Status Register 1
Interrupt Status Register 2
INT Mask Register 1
INT Mask Register 2
VID/Fan Divisor Register
Serial Bus Address Register (Power on reset only, not
reset by Configuration Register INITIALIZATION)
VID4 Register
Temperature Configuration Register
Extended Mode Register 1
Extended Mode Register 2
Configuration Register INITIALIZATION is accomplished by
setting Bit 7 of the Configuration Register high. This bit
automatically clears after being set.
and
Value
RAM
3.3 Using the Configuration Register
The Configuration Register controls the LM81 operation. At
power on, the ADC is stopped and INT_Clear is asserted,
clearing the INT hardwire output. The Configuration Register
starts and stops the LM81, enables and disables interrupt
output, and provides the Reset function described in Section
3.2
Bit 0 of the Configuration Register controls the monitoring
loop of the LM81. Setting Bit 0 low stops the LM81
monitoring loop and puts the LM81 in shutdown mode,
reducing power consumption. Serial Bus communication can
take place with any register in the LM81 although activity on
the SMBData and SMBCLK lines will increase shutdown
current, up to as much as maximum rated supply current,
while the activity takes place. Taking Bit 0 high starts the
monitoring loop, described in more detail subsequently.
Bit 1 of the Configuration Register enables the INT Interrupt
hardwire output when this bit is taken high.
Bit 3 of the Configuration Register clears the INT output
when set high, without affecting the contents of the Interrupt
Status Registers. The LM81 will stop monitoring. It will
resume upon clearing of this bit.
Bit 4 of the Configuration Register provides an active low 20
ms pulse at the RESET output when set high.
The CI_Clear provides an active low 20 ms pulse at the CI
output pin when set high. This is intended for resetting the
Chassis Intrusion circuitry.
The INITIALIZATION bit resets the internal registers of the
LM81 as described in Section 3.2
3.4 Starting Conversions
The monitoring function (Analog inputs, temperature, and
fan speeds) in the LM81 is started by writing to the
Configuration Register and setting INT_Clear (Bit 3), low,
and Start (bit 0), high. The LM81 then performs a
“round-robin” monitoring of all analog inputs, temperature,
and fan speed inputs approximately once every 400 ms. The
sequence of items being monitored corresponds to locations
in the Value RAM and is:
1.
Temperature
2.
Vccp2
3.
+12Vin
4.
+5Vin
5.
+3.3Vin
6.
Vccp1
7.
+2.5Vin
8.
Fan 1
9.
Fan 2
DACOut immediately changes after the DAC Data Register
in the Value RAM has been updated. For a zero to full scale
transition DACOut will typically settle within 100 μsec of the
stop by master in the write to the DAC Data Register Serial
Bus transaction. The DAC Data Register is not reset by the
INITIALIZATION bit found in the Configuration Register.
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM8362_SERIES | |
| LM8363_SERIES | |
| LM8368_SERIES | |
| LM8369 | |
| LM8360 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM81CIMTX-3/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81CIMTX-32 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System |
| LM81DH12 | 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| LM8-1M.5M.1 | 制造商:Banner Engineering 功能描述:LM8-1M.5M.1 LOGIC MOD MULTIBM |
| LM81-S | 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
發布緊急采購，3分鐘左右您將得到回復。