- 您現在的位置：買賣IC網 > PDF目錄358876 > LM80CIMT-3 (NATIONAL SEMICONDUCTOR CORP) Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | LM80CIMT-3 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| 中文描述： | 7-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 |
| 封裝： | PLASTIC, TSSOP-24 |
| 文件頁數： | 19/29頁 |
| 文件大小： | 435K |
| 代理商： | LM80CIMT-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Functional Description
(Continued)
8.0 THE LM80 INTERRUPT STRUCTURE
Figure 10 depicts the Interrupt Structure of the LM80. The
LM80 can generate Interrupts as a result of each of its inter-
nal WATCHDOG registers on the analog, temperature, and
fan inputs.
8.1 INTERRUPT INPUTS
External Interrupts can come from the following sources.
While the label suggests a specific type or source of Inter-
rupt, this label is not a restriction of its usage, and it could
come from any desired source:
BTI -
This is an active low Interrupt intended to come
from the O.S. output of LM75 temperature sensors. The
LM75 O.S. output goes active when its temperature ex-
ceeds a programmed threshold. Up to 8 LM75’s can be
connected to a single Serial Bus bus with their O.S. out-
put’s wire or’d to the BTI input of the LM80. If the tem-
perature of any LM75 exceeds its programmed limit, it
drives BTI low. This generates an Interrupt to notify the
host of a possible overtemperature condition. Provides
an internal pull-up of 10 k
.
CI (Chassis Intrusion) -
from any type of device that detects and captures chassis
intrusion violations. This could be accomplished me-
chanically, optically, or electrically, and circuitry external
to the LM80 is expected to latch the event. The design of
the LM80 allows this input to go high even with no power
applied to the LM80, and no clamping or other interfer-
ence with the line will occur. This line can also be pulled
low for at least 10 ms by the LM80 to reset a typical
Chassis Intrusion circuit. Accomplish this reset by setting
Bit 5 of Configuration Register high. The bit in the Regis-
ter is self-clearing.
This is an active high interrupt
DS100040-18
FIGURE 10. Interrupt Structure
www.national.com
19
相關PDF資料 |
PDF描述 |
|---|---|
| LM80CIMT-31 | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM832 | LM832 Dynamic Noise Reduction System DNR |
| LM832M | LM832 Dynamic Noise Reduction System DNR |
| LM832N | LM832 Dynamic Noise Reduction System DNR |
| LM833D | DUAL OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM80CIMT-3/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM80CIMT-31 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM80CIMT3NOPB | 制造商:Texas Instruments 功能描述:Processor Supervisor 24-Pin TSSOP Rail |
| LM80CIMT5 | 制造商:Texas Instruments 功能描述: |
| LM80CIMT-5 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。