- 您現在的位置：買賣IC網 > PDF目錄358876 > LM80CIMT-3 (NATIONAL SEMICONDUCTOR CORP) Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | LM80CIMT-3 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| 中文描述： | 7-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 |
| 封裝： | PLASTIC, TSSOP-24 |
| 文件頁數： | 11/29頁 |
| 文件大小： | 435K |
| 代理商： | LM80CIMT-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Functional Description
(Continued)
2.2 Serial Bus Interface
The Serial Bus control lines consists of the SDA(serial data),
SCL (serial clock) and A0-A1 (address) pins. The LM80 can
only operate as a slave. The SCL line only controls the serial
interface, all other clock functions within LM80 such as the
ADC and fan counters are done with a separate asynchro-
nous internal clock.
When using the Serial Bus Interface a write will always con-
sist of the LM80 Serial Bus Interface Address byte, followed
by the Internal Address Register byte, then the data byte.
There are two cases for a read:
1.
If the Internal Address Register is known to be at the de-
sired Address, simply read the LM80 with the Serial Bus
Interface Address byte, followed by the data byte read
from the LM80.
2.
If the Internal Address Register value is unknown, write
to the LM80 with the Serial Bus Interface Address byte,
followed by the Internal Address Register byte. Then re-
start the Serial Communication with a Read consisting of
the Serial Bus Interface Address byte, followed by the
data byte read from the LM80.
The default power on Serial Bus address for the LM80 is:
0101(A2)(A1)(A0) binary, where A0-A2 reflect the state of
the pins defined by the same names.
All of these communications are depicted in the Serial Bus
Interface Timing Diagrams as shown in Figure 5
DS100040-8
(a) Serial Bus Write to the Internal Address Register followed by the Data Byte
DS100040-9
(b) Serial Bus Write to the Internal Address Register Only
DS100040-10
(c) Serial Bus Read from a Register with the Internal Address Register Preset to Desired Location
FIGURE 5. Serial Bus Timing
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM80CIMT-31 | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM832 | LM832 Dynamic Noise Reduction System DNR |
| LM832M | LM832 Dynamic Noise Reduction System DNR |
| LM832N | LM832 Dynamic Noise Reduction System DNR |
| LM833D | DUAL OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM80CIMT-3/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM80CIMT-31 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM80CIMT3NOPB | 制造商:Texas Instruments 功能描述:Processor Supervisor 24-Pin TSSOP Rail |
| LM80CIMT5 | 制造商:Texas Instruments 功能描述: |
| LM80CIMT-5 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。