參數資料
型號: LM4935
廠商: National Semiconductor Corporation
元件分類: ADC
英文描述: Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC
中文描述: 音頻子系統的雙模單聲道立體聲耳機和揚聲器放大器的高效率和多功能模數轉換器
文件頁數: 55/112頁
文件大小: 5017K
代理商: LM4935
12.0 Status & Control Registers
(Continued)
12.32 DIGITAL AUDIO DATA FORMATS
I2S master mode can only be used when the DAC is enabled unless the ADC_I2S_M bit is set. PCM Master mode can only be
used when the ADC is enabled. If the PCM receiver interface is operated in slave mode the clock and sync should be enabled
at the same time as the PCM receiver uses the first PCM frame to calculate the PCM interface format. This format can not be
changed unless a soft reset is issued. It is strongly recommended that the LM4935 is operated in master mode as this eliminates
the risk of sample rate mismatch between the data converters and the audio interfaces.
In master mode the I2S_CLK has a 60/40 duty cycle and a frequency of 50*fs. In slave mode the PCM and I2S receivers only
record the 1st 16 and 18 bits of the serial words respectively. The I2S format is as follows:
When SAR SDO data is passed to the I2S, it is left aligned (MSB aligned) to allow lower I2S resolutions to be used.
If the DAC is driven from the PCM interface then the left channel of the DAC is used and the right channel is inactive.
20134115
FIGURE 10. I
2
S Serial Data Format (Default Mode)
20134116
FIGURE 11. PCM Serial Data Format (16 bit Slave Example)
L
www.national.com
55
相關PDF資料
PDF描述
LM4935WL Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC
LM4935WLX Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC
LM4936 Stereo 2W Audio Power Amplifiers with Volume Control and Selectable Control Interface (SPI or I2C)
LM4951 Wide Voltage Range 1.8 Watt Audio Amplifier
LM4953 Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver
相關代理商/技術參數
參數描述
LM49350 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Performance Audio Codec Sub-System with a Ground-Referenced Stereo Headphone Amplifier
LM49350RL 制造商:Texas Instruments 功能描述:Audio Codec 1ADC / 1DAC 36-Pin uSMD T/R 制造商:Texas Instruments 功能描述:AUDIO CODEC SUBSYSTEM 36MICRO SMDXT
LM49350RL/NOPB 功能描述:接口—CODEC Hi Perf Audio Codec Subsystem RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
LM49350RL/NOPB 制造商:Texas Instruments 功能描述:Audio Codec IC
LM49350RLEVAL 功能描述:音頻 IC 開發工具 LM49350RL EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V