- 您現在的位置：買賣IC網 > PDF目錄385487 > LM4935 (National Semiconductor Corporation) Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC PDF資料下載
參數資料
| 型號： | LM4935 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | ADC |
| 英文描述： | Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC |
| 中文描述： | 音頻子系統的雙模單聲道立體聲耳機和揚聲器放大器的高效率和多功能模數轉換器 |
| 文件頁數： | 50/112頁 |
| 文件大?。?/td> | 5017K |
| 代理商： | LM4935 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
12.0 Status & Control Registers
(Continued)
12.29 HEADSET DETECT OVERVIEW
The LM4935 has built in monitors to automatically detect headset insertion or removal. The detection scheme can differentiate
between mono, stereo, mono-cellular and stereo-cellular headsets. Upon detection of headset insertion or removal, the LM4935
updates read-only bit 0 - headset absence/presence, bit 1- mono/stereo headset and bit 2 - headset without mic / with mic, of the
STATUS register (0x18h). Headset insertion/removal and headset type can also be detected in standby mode; this consumes no
analog supply current when the headset is absent.
The LM4935 can be programmed to raise an interrupt (set the IRQ pin high) when headset insert/removal is sensed by setting
bit 0 of DETECT (0x17h). When headset detection is enabled in active mode and a headset is not detected, the HPL_OUT and
HPR_OUT amplifiers will be disabled (switched off for capless mode and muted forAC-coupled mode) and the EXT_BIAS pin will
be disconnected from the MIC_BIAS amplifier, irrespective of control register settings.
The LM4935 also has the capability to detect button press, when a button is present on the headset microphone. Both parallel
button-type (in parallel with the headset microphone, default value) and series button-type (in series with the headset micro-
phone) can be detected; the button type used needs to be defined in bit 3 of MIC_2 (0x0Ch). Button press can also be detected
in stand-by mode; this consumes 10 μA of analog supply current for a series type push button and 100 μA for a parallel type push
button. Upon button press, the LM4935 updates bit 3 of STATUS (0x18h). In active OCL mode, with internal microphone selected
(INT_EXT = 0; (reg 0x0Bh)), if a parallel pushbutton headset is inserted into the system, INT_EXT must be set high before BTN
(bit 3 of STATUS (0x18h)) can be read. The LM4935 can also be programmed to raise an interrupt on the IRQ pin when button
press is sensed by setting bit 1 of DETECT.
The LM4935 provides debounce programmability for headset and button detect. Debounce programmability can be used to reject
glitches generated, and hence avoid false detection, while inserting/removing a headset or pressing a button.
Headset insert/removal debounce time is defined by HS_DBNC_TIME; bits 6:3 of DETECT (0x17h). Parallel button press
debounce time is defined by BTN_DBNC_TIME; bits 5:4 of MIC_2 (0x0Ch).
Note that since the first effect of a series button press (microphone disconnected) is indistinguishable from headset removal, the
debounce time for series button press in defined by HS_DBNC_TIME.
Headset and push button detection can be enabled by setting CHIP_MODE 0; bit 0 of BASIC (0x00h). For reliable headset / push
button detection all following bits should be defined before enabling the headset detection system:
1) the OCL-bit (AC-Coupled / Capless headphone interface (bit 7 of BASIC (0x00h))
2) the headset insert/removal debounce settings (bit 6:3 of DETECT (0x17h))
3) the BTN_TYPE-bit (Parallel / Series push button type (bit 3 of MIC_2 (0x0Ch))
4) the parallel push button debounce settings (bit 5:4 of MIC_2 (0x0Ch))
Figure 8 shows terminal connections and jack configuration for various headsets. Care should be taken to avoid any DC path from
the MIC_DET pin to ground when a headset is not inserted.
L
www.national.com
50
相關PDF資料 |
PDF描述 |
|---|---|
| LM4935WL | Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC |
| LM4935WLX | Audio Sub-System with Dual-Mode Stereo Headphone and Mono High Efficiency Loudspeaker Amplifiers and Multi-Purpose ADC |
| LM4936 | Stereo 2W Audio Power Amplifiers with Volume Control and Selectable Control Interface (SPI or I2C) |
| LM4951 | Wide Voltage Range 1.8 Watt Audio Amplifier |
| LM4953 | Ground-Referenced, Ultra Low Noise, Ceramic Speaker Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM49350 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Performance Audio Codec Sub-System with a Ground-Referenced Stereo Headphone Amplifier |
| LM49350RL | 制造商:Texas Instruments 功能描述:Audio Codec 1ADC / 1DAC 36-Pin uSMD T/R 制造商:Texas Instruments 功能描述:AUDIO CODEC SUBSYSTEM 36MICRO SMDXT |
| LM49350RL/NOPB | 功能描述:接口—CODEC Hi Perf Audio Codec Subsystem RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| LM49350RL/NOPB | 制造商:Texas Instruments 功能描述:Audio Codec IC |
| LM49350RLEVAL | 功能描述:音頻 IC 開發工具 LM49350RL EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
發布緊急采購，3分鐘左右您將得到回復。