- 您現在的位置：買賣IC網 > PDF目錄385480 > LM3224MMX-ADJ (NATIONAL SEMICONDUCTOR CORP) 615kHz/1.25MHz Step-up PWM DC/DC Converter PDF資料下載
參數資料
| 型號： | LM3224MMX-ADJ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 615kHz/1.25MHz Step-up PWM DC/DC Converter |
| 中文描述： | 2.8 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 12/18頁 |
| 文件大?。?/td> | 920K |
| 代理商： | LM3224MMX-ADJ |
Operation
(Continued)
where R
is the output impedance of the error amplifier,
approximately 900k
. Since R
is generally much less than
R
, it does not have much effect on the above equation and
can be neglected until a value is chosen to set the zero f
.
f
is created to cancel out the pole created by the output
capacitor, f
. The output capacitor pole will shift with differ-
ent load currents as shown by the equation, so setting the
zero is not exact. Determine the range of f
over the ex-
pected loads and then set the zero f
to a point approxi-
mately in the middle. The frequency of this zero is deter-
mined by:
Now R
can be chosen with the selected value for C
.
Check to make sure that the pole f
is still in the 10Hz to
500Hz range, change each value slightly if needed to ensure
both component values are in the recommended range.
HIGH OUTPUT CAPACITOR ESR COMPENSATION
When using an output capacitor with a high ESR value, or
just to improve the overall phase margin of the control loop,
another pole may be introduced to cancel the zero created
by the ESR. This is accomplished by adding another capaci-
tor, C
, directly from the compensation pin V
to ground, in
parallel with the series combination of R
C
and C
C
. The pole
should be placed at the same frequency as f
Z1
, the ESR
zero. The equation for this pole follows:
To ensure this equation is valid, and that C
C2
can be used
without negatively impacting the effects of R
C
and C
C
, f
PC2
must be greater than 10f
ZC
.
CHECKING THE DESIGN
With all the poles and zeros calculated the crossover fre-
quency can be checked as described in the section
DC Gain
and Open-loop Gain
. The compensation values can be
changed a little more to optimize performance if desired.
This is best done in the lab on a bench, checking the load
step response with different values until the ringing and
overshoot on the output voltage at the edge of the load steps
is minimal. This should produce a stable, high performance
circuit. For improved transient response, higher values of R
C
should be chosen. This will improve the overall bandwidth
which makes the regulator respond more quickly to tran-
sients. If more detail is required, or the most optimum per-
formance is desired, refer to a more in depth discussion of
compensating current mode DC/DC switching regulators.
POWER DISSIPATION
The output power of the LM3224 is limited by its maximum
power dissipation. The maximum power dissipation is deter-
mined by the formula
P
D
= (T
jmax
- T
A
)/
θ
JA
where T
is the maximum specidfied junction temperature
(125C), T
is the ambient temperature, and
θ
JA
is the ther-
mal resistance of the package.
LAYOUT CONSIDERATIONS
The input bypass capacitor C
, as shown in the typical
operating circuit, must be placed close to the IC. This will
reduce copper trace resistance which effects input voltage
ripple of the IC. For additional input voltage filtering, a 100nF
bypass capacitor can be placed in parallel with C
, close to
the V
pin, to shunt any high frequency noise to ground. The
output capacitor, C
, should also be placed close to the
IC. Any copper trace connections for the C
capacitor can
increase the series resistance, which directly effects output
voltage ripple. The feedback network, resistors R
and
R
FB2
, should be kept close to the FB pin, and away from the
inductor, to minimize copper trace connections that can in-
ject noise into the system. Trace connections made to the
inductor and schottky diode should be minimized to reduce
power dissipation and increase overall efficiency. For more
detail on switching power supply layout considerations see
Application Note AN-1149:
Layout Guidelines for Switching
Power Supplies
.
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM3310 | Step-up PWM DC/DC Converter with Integrated Op-Amp and Gate Pulse Modulation Switch |
| LM3310SQ | Step-up PWM DC/DC Converter with Integrated Op-Amp and Gate Pulse Modulation Switch |
| LM3310SQX | Step-up PWM DC/DC Converter with Integrated Op-Amp and Gate Pulse Modulation Switch |
| LM3351 | Switched Capacitor Voltage Converter |
| LM3351MM | Switched Capacitor Voltage Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3224MMX-ADJ/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM322H | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Precision Timers |
| LM322N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Precision Timers |
| LM322N/B+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Timer Circuit |
| LM323 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Three-terminal 3 A adjustable voltage regulators |
發布緊急采購，3分鐘左右您將得到回復。