參數資料
型號: LM2635M/NOPB
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO20
封裝: PLASTIC, SOP-20
文件頁數: 3/13頁
文件大?。?/td> 734K
代理商: LM2635M/NOPB
Applications Information (Continued)
INDUCTOR SELECTION
The size of the output is determined by a number of param-
eters. Basically the larger the inductor, the smaller the output
ripple voltage, but the slower the converter’s response
speed during a load transient. On the other hand, a smaller
inductor requires higher switching frequency to maintain the
same level of output ripple, and probably results in a more
lossy converter, but has less inertia responding to load tran-
sient. In the case of Pentium II power supply, fast recovery of
the load voltage from transient window back to the steady
state window is considered important. This limits the highest
inductance value that can be used. The lowest inductance
value is limited by the highest switching frequency that can
be practically employed. As the switching frequency in-
creases, the switching loss in the MOSFETs tends to in-
crease, resulting in less converter efficiency and larger heat
sinks. A good switching frequency is probably a frequency
under which the MOSFET conduction loss is higher than the
switching loss because the cost of the MOSFET is directly
related to its R
DSON. The inductor size can be determined by
the following equation:
where V
O_RIP is the peak-to-peak output ripple voltage, f is
the switching frequency. For commonly used low R
DSON
MOSFETs, a reasonable switching frequency is 300 kHz.
Assume an output peak-peak ripple voltage of 18 mV is to be
guaranteed, the total output capacitor ESR is 9 m
, the input
voltage is 5V, and output voltage is 2.8V. The inductance
value according to the above equation will then be 2 H. The
highest slew rate of the inductor current when the load
changes from no load to full load can be determined as
follows:
where D
MAX is the maximum allowed duty cycle, which is
around 0.9 for LM2635. For a load transient from 0A to 14A,
the highest current slew rate of the inductor, according to the
above equation, is 0.85A/s, and therefore the shortest pos-
sible total recovery time is 14A/(0.85A/s) = 16.5 s. Notice
that the output voltage starts to recover whenever the induc-
tor starts to supply current.
The highest slew rate of the inductor current when the load
changes from full load to no load can be determined from the
same equation, but use D
MIN instead of DMAX.
Since the D
MIN of LM2635 at 300 kHz is 0%, the slew rate is
therefore 1.4A/s. So the approximate total recovery time
will be 14A/(1.4A/s) = 10 s.
The input inductor is for limiting the input current slew rate
during a load transient. In the case that low ESR aluminum
electrolytic capacitors are used for the input capacitor bank,
voltage change due to capacitor charging/discharging is usu-
ally negligible for the first 20 s. ESR is by far the dominant
factor in determining the amount of capacitor voltage
undershoot/overshoot due to load transient. So the worst
case is when the load changes between no load and full
load, under which condition the input inductor sees the high-
est voltage change across the input capacitors. Assume the
input capacitor bank is made up of three 16MV820GX, i.e.,
the total ESR is 15 m
. Whenever there is a sudden load
current change, it has to initially be supported by the input
capacitor bank instead of the input inductor. So for a full load
swing between 0A and 14A, the voltage seen by the input
inductor is
V=14A x15m = 210 mV. Use the following
equation to determine the minimum inductance value:
where (di/dt)
MAX is the maximum allowable input current
slew rate, which is 0.1A/s in the case of the Pentium II
power supply. So the input inductor size, according to the
above equation, should be 2.1 H.
DYNAMIC POSITIONING OF LOAD VOLTAGE
Since the Intel VRM specifications have defined two operat-
ing windows for the MPU core voltage, one being the steady
state window and the other the transient window, it is a good
idea to dynamically position the steady state output voltage
in the steady state window with respect to load current level
so that the output voltage has more headroom for load
transient response. This requires information about the load
current. There are at least two simple ways to implement this
idea with LM2635. One is to utilize the output inductor DC
resistance, see Figure 7. The average voltage across the
output inductor is actually that across its DC resistance. That
average voltage is proportional to load current.
Since the switching node voltage V
A bounces between the
input voltage and ground at the switching frequency, it is
impossible to choose point A as the feedback point, other-
wise the dynamic performance will suffer and the system
may have some noise problems. Using a low pass filter
network around the inductor, such as the one shown in the
figure, seems to be a good idea. The feedback point is C.
Since at the switching frequency the impedance of the 0.1
F is much less than 5 k
, the bouncing voltage at point A
will be mainly applied across the resistor 5 k
, and point C
will be much quieter than A. However, V
CB average is still the
majority of V
AB average, because of the resistor divider. So
in steady state V
C =IO xrL +VCORE, where rL is the inductor
DC resistance. So at no load, output voltage is equal to V
C,
and at full load, output voltage is I
O xrL lower than VC.To
further utilize the steady state window, a resistor can be
10011926
FIGURE 7. Dynamic Voltage Positioning by Utilizing
Output Inductor DC Resistance
LM2635
www.national.com
11
相關PDF資料
PDF描述
LM2676SDX-12/NOPB 5.4 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, DSO14
LM2678LD-12 8.75 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, DSO14
LM2678LDX-5.0 8.75 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, DSO14
LM2678LD-3.3 8.75 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, DSO14
LM2678LD-5.0 8.75 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, DSO14
相關代理商/技術參數
參數描述
LM2635MX 功能描述:IC REG SYNCH BUCK 5-BIT 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像,聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP(8x8) 包裝:管件
LM2635MX/NOPB 制造商:Texas Instruments 功能描述:Conv DC-DC Single Step Down 20-Pin SOIC W T/R
LM2636 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5-Bit Programmable Synchronous Buck Regulator Controller
LM2636A E WAF 制造商:Texas Instruments 功能描述:
LM2636AM E WAF 制造商:Texas Instruments 功能描述: