參數資料
型號： LK4301-7ER
廠商： POWER-ONE INC
元件分類： 電源模塊
英文描述： 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
封裝： HEAT SINK, METAL, CASE K02
文件頁數： 5/28頁
文件大?。?/td> 627K
代理商： LK4301-7ER
BCD20001-G Rev AB
Page 13 of 28
www.power-one.com
K Series with PFC Data Sheet
150 – 280 Watt AC-DC Converters
Auxiliary Functions
Inhibit for Remote On/Off
The outputs may be enabled or disabled by means of a
logic signal (TTL, CMOS, etc.) applied between the inhibit
input i and pin 18 (S– or Vo1–). In systems with several
converters, this feature can be used to control the
activation sequence of the converters. If the inhibit function
is not required, connect the inhibit pin 18 to pin 14.
Note: If pin 18 is not connected, the output is disabled.
Vi+
Vi–
Vo–
i
Vo+
Iinh
Vinh
06031
Fig. 18
Definition of Vinh and Iinh.
Table 8: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Vinh Inhibit
Vo = on
Vi min – Vi max
– 50
0.8
V
voltage
Vo = off
2.4
50
I inh
Inhibit current
Vinh = 0
– 400
A
t r
Rise time
30
ms
t f
Fall time
depending on Io
Fig. 20
Output response as a function of inhibit control
Fig. 19
Typical inhibit current I inh versus inhibit voltage Vinh
1.6
0.8
0
–0.8
–50
Vinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Vinh = 0.8 V
Vo = on
Vo = off
Vinh = 2.4 V
06032
0
t
0
Inhibit
1
0.1
1
Vo/Vo nom
tr
tf
06001
Sense Lines (Single-Output Models)
Important:
Sense
lines
must
always
be
connected!
Incorrectly
connected
sense
lines
may
activate
the
overvoltage protection resulting in a permanent short-circuit
of the output.
This feature allows for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. We recommend connecting the sense lines
directly at the female connector.
To ensure correct operation, both sense lines (S+, S–)
should be connected to their respective power outputs
(Vo1+ and Vo1–), and the voltage difference between any
sense line and its respective power output (as measured
on the connector) should not exceed the following values:
Table 9: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
<0.5 V
<0.25 V
12 V, 15 V, 24 V
<1.0 V
<0.25 V
Note: If the output voltages are increased above Vo nom via
R-input control, option P setting, remote sensing or option T,
the output currents must be reduced accordingly, so that
Po nom is not exceeded.
Programmable Output Voltage (R-Function)
As a standard feature, the converters offer an adjustable
output
voltage,
identified
by
letter
R
in
the
type
designation. The control input R (pin 16) accepts either a
control voltage Vext or a resistor Rext to adjust the desired
output voltage. When R is not connected, the output
voltage is set to Vo nom.
a) Adjustment by means of an external control voltage Vext
between pin 16 (R) and pin 14:
The control voltage range is 0 – 2.75 VDC and allows an
output voltage adjustment in the range of approximately
0 – 110% Vo nom.
Vo
Vext
≈ –––––– 2.5 V
Vo nom
b) Adjustment by means of an external resistor:
Depending upon the value of the required output voltage
the resistor shall be connected
either: Between pin 16 and pin 14 (Vo
< Vo nom) to
achieve an output voltage adjustment range of approxi-
mately 0 – 100% Vo nom.
or: Between pin 16 and pin 12 (Vo > Vo nom) to achieve an
output voltage adjustment range of 100 – 110% Vo nom.
Warning:
– Vext shall never exceed 2.75 VDC.
– The value of R'ext shall never be less than the lowest
value as indicated in table R'ext (for V0
> V0 nom) to
avoid damage to the converter!
相關PDF資料
PDF描述
LK4301-9PD5TB1 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
LK5660-7ERD5TB1 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
LK4501-9RD1TB1 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
LK4601-7ERD3TB1 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
LK5660-7ERD2TB1 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE
相關代理商/技術參數
參數描述
LK4301-7R 功能描述:線性和開關式電源 Euro-Cassette 144W (12V) RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度:
LK4301-9ER 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 12V 12A 280W 15PIN - Bulk
LK4303-9ERD4T 制造商:Power-One 功能描述:- Bulk
LK4402 制造商:CLINCH NUT 功能描述:
LK-440-2 制造商:PennEngineering (PEM) 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*