參數資料
型號： LIS3L02DS
廠商： STMICROELECTRONICS
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PDSO24
封裝： PLASTIC, SO-24
文件頁數： 16/18頁
文件大?。?/td> 511K
代理商： LIS3L02DS
7/18
LIS3L02DS
2
DIGITAL INTERFACES
The registes embedded inside the LIS3L02DS may be accessed through both the 2C and SPI serial in-
terfaces. The latter may be SW configured to operate either in SPI mode or in 3-wire interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I2C interface, CS line must be
tied high (i.e connected to Vdd).
Table 1. Serial Interface Pin Description
2.1 I2C Serial Interface
The LIS3L02DS I2C is a bus slave. The I2C is employed to write the data into the registers whose content
can also be read back.
The relevant I2C terminology is given in the table below
Table 2. Serial Interface Pin Description
There are two signals associated with the I2C bus: the Serial Clock Line (SCL) and the Serial DAta liine
(SDA). The latter is a bidirectional line used for sending and receiving the data to/form the interface. Both
the lines are connected to Vdd through a pull-up resistor embedded inside the LIS3L02DS. When the bus
is free both the lines are high.
2.1.1 I2C Operation
The transaction on the bus is started through a START signal. A START condition is defined as a HIGH
to LOW transition on the data line while the SCL line is held HIGH. After this has been transmitted by the
Master, the bus is considered busy. The next byte of data transmitted after the start condition contains the
address of the slave in the first 7 bits and the eighth bit tells whether the Master is receiving data from the
slave or transmitting data to the slave. When an address is sent, each device in the system compares the
first seven bits after a start condition with it’s address. If they match, the device considers itself addressed
by the Master. The address can be made up of a programmable part and a fixed part, thus allowing more
than one device of the same type to be connected to the I2C bus.
The Slave ADdress (SAD) associated to the LIS3L02DS is 0011101.
Data transfer with acknowledge is mandatory. The transmitter must release the SDA line during the ac-
PIN Name
PIN Description
CS
SPI enable
I2C/SPI mode selection (1: I2C mode; 0: SPI enabled)
SCL/SPC
I2C Serial Clock (SCL)
SPI Serial Port Slock (SPC)
SDA/SDI/SDO
I2C Serial Data (SDA)
SPI Serial Data Input (SDI)
3-wire Interface Serial Data Output (SDO)
SDO
SPI Serial Data Output (SDO)
Term
Description
Transmitter
The device which sends data to the bus
Receiver
The device which receives data from the bus
Master
The device which initiates a transfer, generates clock signals and terminates a transfer
Slave
The device addressed by the master
相關PDF資料
PDF描述
LIS3LV02DL SPECIALTY ANALOG CIRCUIT, PBGA16
LM10010SD SWITCHING REGULATOR, PDSO10
LM10010SDX SWITCHING REGULATOR, PDSO10
LM12L458CIVX SPECIALTY ANALOG CIRCUIT, PQCC44
LM185BYH-MLS 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3
相關代理商/技術參數
參數描述
LIS3L06AL 功能描述:加速計 - 板上安裝 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3L06AL_06 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR-3-axis - +/-2g/6g ultracompact linear accelerometer
LIS3L06ALTR 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3LV02DL 功能描述:加速計 - 板上安裝 MEMS INERTIAL SENSOR RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3LV02DL_08 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*