- 您現在的位置：買賣IC網 > PDF目錄69004 > LIS3L02DS (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | LIS3L02DS |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封裝： | PLASTIC, SO-24 |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 511K |
| 代理商： | LIS3L02DS |
LIS3L02DS
6/18
1.2 IC Interface
The complete measurement chain is composed by a low-noise capacitive amplifier which converts into an
analog voltage the capacitive unbalancing of the MEMS sensor and by three
Σ analog-to-digital convert-
ers, one for each axis, that translates the produced signal into a digital bitstream.
The
Σ converters are tigthly coupled with dedicated reconstruction filters which removes the high fre-
quency components of the quantization noise and provides low rate and high resolution digital words.
The charge amplifier and the
Σ converters are operated respectively at 107.5 KHz and 35.8 KHz.
The data rate at the output of the reconstruction depends on the user selected Decimation Factor (DF)
and span from 280 Hz to 4.48 KHz.
The acceleration data may be accessed through an I2C/SPI interface thus making the device particularly
suitable for direct interfacing with a microcontroller.
The LIS3L02DS features a Data-Ready signal (DRY) which indicated when a new set of measured accel-
eration data is available thus simplifying data synchronization in digital system employing the device itself.
The LIS3L02DS may also be configured to generate an inertial wake-up/interrupt signal when a program-
mable acceleration threshold is exceeded along one of the three axis.
1.3 Factory calibration
The IC interface is factory calibrated to provide to the final user a device ready to operate. The parameters
which are trimmed are: gain, offset, common mode and internal clock frequency.
The trimming values are stored inside the device by a non volatile structure. Any time the device is turned
on, the trimming parameters are downloaded into the registers to be employed during the normal opera-
tion thus allowing the final user to employ the device without any need for further calibration
相關PDF資料 |
PDF描述 |
|---|---|
| LIS3LV02DL | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LM10010SD | SWITCHING REGULATOR, PDSO10 |
| LM10010SDX | SWITCHING REGULATOR, PDSO10 |
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LM185BYH-MLS | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS3L06AL | 功能描述:加速計 - 板上安裝 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L06AL_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR-3-axis - +/-2g/6g ultracompact linear accelerometer |
| LIS3L06ALTR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DL | 功能描述:加速計 - 板上安裝 MEMS INERTIAL SENSOR RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DL_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer |
發布緊急采購，3分鐘左右您將得到回復。