參數資料
型號： LH28F040SUTD-Z4
廠商： Sharp Corporation
英文描述： 4M (512K 】 8) Flash Memory
中文描述： 4分（為512k】8）閃存
文件頁數： 9/32頁
文件大小： 247K
代理商： LH28F040SUTD-Z4
4M (512K × 8) Flash Memory
LH28F040SUTD-Z4
9
4M DUAL WORK FLASH MEMORY
SOFTWARE ALGORITHMS
Overview
With the advanced Command User Interface, its Per-
formance Enhancement commands and Status Regis-
ters, the software code required to perform a given
operation may become more intensive but it will result
in much higher write/erase performance compared with
current flash memory architectures.
The software flowcharts describing how a given
operation proceeds are shown here. Figures 4 through
6 depict flowcharts using the 2nd generation flash
device in the LH28F008SA-compatible mode. Figures
7 through 12 depict flowcharts using the 2nd genera-
tion flash device’s performance enhancement com-
mands mode.
When the device power-up or reset is completed, Set
Write Protect command must be written to both the bank
selected by BE
0
and BE
1
in order to reflect actual block
lock status.
When the device power-up or reset is completed, all
blocks come up locked. Therefore, Byte Write, Two Byte
Serial Write and Block Erase can not be performed in
each block. However, at that time, Erase All Unlocked
Block is performed normally, if used, and reflect actual
lock status, also the unlocked block data is erased. When
the device power-up or reset is completed, Set Write
Protect command must be written to reflect actual block
lock status.
Reset Write Protect command must be written be-
fore Write Block Lock command. To reflect actual block
lock status, Set Write Protect command is succeeded.
The Compatible Status Register (CSR) used to
determine which blocks are locked. In order to see Lock
Status of certain block, a Byte Write command (WA =
Block Address, WD = FHH) is written to the CUI, after
issuing Set Write Protect command. If CSR.7, CSR.5
and CSR.4 (WSMS, ES and DWS) are set to ‘1’s, the
block is locked. If CSR.7 is set to ‘1’, the block is not
locked.
Reset Write Protect command enables Write/Erase
operation to each block.
In the case of Block Erase is performed, the block
lock information is also erased. Block Lock command
and Set Write Protect command must be written to pro-
hibit Write/Erase operation to each block.
There are unassigned commands. It is not recom-
mended that the customer use any command other than
the valid commands specified in “Command Bus Defi-
nitions”. Sharp reserved the right to redefine these codes
for future functions.
相關PDF資料
PDF描述
LH28F160BHE-TTL90 16M (x8/x16) Flash Memory
LH28F160BJE-BTL90 16M-BIT(1Mbit x16/2Mbit x8)Boot Block Flash MEMORY(16M位(1M位 x16/2M位 x8)Boot Block 閃速存儲器)
LH28F160BJE-TTL70 16M-BIT(1Mbit x16/2Mbit x8)Boot Block Flash MEMORY(16M位(1M位 x16/2M位 x8)Boot Block 閃速存儲器)
LH28F160BJHE-BTL70 16M-BIT(1Mbit x16/2Mbit x8)Boot Block Flash MEMORY(16M位(1M位 x16/2M位 x8)Boot Block 閃速存儲器)
LH28F160BJHE-TTL90 16M-BIT ( 1Mbit x16 / 2Mbit x8 )Boot Block Flash MEMORY(16M位( 1M位 x16 / 2M位 x8 )Boot Block 閃速存儲器)
相關代理商/技術參數
參數描述
LH28F0I6SCT-L95 制造商:Sharp Microelectronics Corporation 功能描述:
LH28F128BFHT-PBTL75A 功能描述:閃存 128Mb (x16)3V OTP Single Supply RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
LH28F128SPHTD-PTLZ5 制造商:Sharp Microelectronics 功能描述:128M MULTI LEVEL CELL 120NS 制造商:Sharp Microelectronics Corporation 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 16MX8/8MX16 120NS 56TSOP - Trays
LH28F160BGH-TL 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:16 M-bit (1 MB x 16) Smart 3 Flash Memories
LH28F160BG-TL 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:16 M-bit (1 MB x 16) Smart 3 Flash Memories
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*