- 您現在的位置：買賣IC網 > PDF目錄358759 > LC72322N (Sanyo Electric Co.,Ltd.) Single-Chip Microcontroller with Built-in LCD Driver and PLL Circuits(用于電子調諧的單片微控制器（帶內置LCD驅動器和鎖相環電路 ）) PDF資料下載
參數資料
| 型號： | LC72322N |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Chip Microcontroller with Built-in LCD Driver and PLL Circuits(用于電子調諧的單片微控制器（帶內置LCD驅動器和鎖相環電路 ）) |
| 中文描述： | 單片微控制器，帶有內置LCD驅動器和PLL電路（用于電子調諧的單片微控制器（帶內置液晶顯示驅動器和鎖相環電路）） |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 202K |
| 代理商： | LC72322N |
Continued from preceding page.
No. 5945-9/13
LC72321N, 72322N, 72323N
Pin No.
Pin
Description
I/O
I/O circuit
HCTR
70
Input
Universal counter input.
Input must be supplied through a coupling capacitor.
The input frequency range is 0.4 to 12 MHz
This pin can be used effectively for FM IF or AM IF
counting.
Universal counter input.
ADI
69
Input
A/D converter input.
This converter requires 1.28 ms to perform a 6-bit
sequential comparison conversion.
Full scale (a data value of 3F (hexadecimal))
corresponds to (63/96) time V
DD
.
LCTR
71
Input must be supplied through a coupling capacitor
when the input frequency is in the range 100 to
500 kHz.
No input coupling capacitor is required when the input
frequency is in the range 1 Hz to 20 kHz.
This pin can be used effectively for AM IF counting.
This pin can also be used as a normal input port.
INT
66
Input
External interrupt request input.
An interrupt occurs when the INTEN flag is set with the
SS instruction and a falling edge is input.
This pin can also be used as a normal input port.
EO1
EO2
77
78
Output
These pins are used as the reference frequency output
and the phase comparator error output for the
programmable divider.
A charge pump circuit is built in.
EO1 and EO2 are the same.
SNS
72
Input
Input used to recognize power failures when the IC is in
backup mode.
This pin can also be used as a normal input port.
HOLD
67
Input
Input used to set the IC to hold mode.
The IC switches to hold mode when the HOLDEN flag
is set with the SS instruction and the HOLD pin is set
low.
A high-voltage handling circuit is used so that this pin
can be linked to the power switch in typical systems.
RES
68
Input
System reset input.
Applications must hold this input low for at least 75 ms
to effect a power on reset.
To start a reset, this pin must be held low for a full 6
base clock cycles.
XIN
XOUT
1
80
Input
Output
Crystal oscillator connections
(4.5 MHz)
Feedback resistors are built in.
TEST1
TEST2
2
79
—
IC test pins. These pins must be either left open or
connected to V
SS
.
—
V
DD
V
SS
31, 73
76
—
Power supply
—
相關PDF資料 |
PDF描述 |
|---|---|
| LC72322 | Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323-XXXX | LED RED/AMBR DIFFUSED(WHITE)RND |
| LC72323 | Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323R | Single-Chip Microcontroller with PLL and LCD Driver |
| LC7232N | CLAMP, CAPACITOR; Centres, fixing:57mm; Diameter, clip:40mm; Length / Height, external:14mm RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72322R | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC72321N |
| LC72323R | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。