參數資料
型號： LAN91C96I-MU
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 微控制器/微處理器
英文描述： NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
中文描述： 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100
封裝： 1 MM THICKNESS, LEAD FREE, TQFP-100
文件頁數： 43/110頁
文件大?。?/td> 655K
代理商： LAN91C96I-MU
Non-PCI Single-Chip Full Duplex Ethernet Controller
SMSC DS – LAN91C96I
Page 43
Rev.
11/18/2004
DATASHEET
INT SEL1-0 - In Local Bus mode, used to select one out of four interrupt pins. The three unused interrupts
are tristated.
INT SEL1
INT SEL0
INTERRUPT PIN USED
0
0
INTR0
0
1
INTR1
1
0
INTR2
1
1
INTR3
I/O SPACE - BANK1
OFFSET
2
NAME
TYPE
SYMBOL
BAR
BASE ADDRESS REGISTER
READ/WRITE
For Local Bus mode only, this register holds the I/O address decode option chosen for the I/O and ROM
space. It is part of the EEPROM saved setup, and is not usually modified during run-time.
A15
0
A14
0
A13
0
A9
1
A8
1
A7
0
A6
0
A5
0
ROM SIZE
RA18
1
RA17
0
RA16
0
RA15
1
RA14
1
0
1
1
A15 - A13 and A9 - A5 - These bits are compared in Local Bus mode against the I/O address on the bus to
determine the IOBASE for LAN91C96I registers. The 64k I/O space is fully decoded by the LAN91C96I
down to a 16 location space, therefore the unspecified address lines A4, A10, A11 and A12 must be all
zeros.
ROM SIZE - Determines the ROM decode area in Local Bus mode memory space as follows:
00 = ROM disable
01 = 16k: RA14-18 define ROM select.
10 = 32k: RA15-18 define ROM select.
11 = 64k: RA16-18 define ROM select.
RA18-RA14 - These bits are compared in Local Bus mode against the memory address on the bus to
determine if the ROM is being accessed, as a function of the ROM SIZE. ROM accesses are read only
memory accesses defined by MEMRD* going low.
For a full decode of the address space unspecified upper address lines have to be: A19 = "1", A20-A23
lines are not directly decoded, however Local Bus systems will only activate SMEMRD* only when A20-
A23=0.
All bits in this register are loaded from the serial EEPROM in Local Bus Mode only.
The I/O base decode defaults to 300h (namely, the high byte defaults to 18h). ROM SIZE defaults to 01.
ROM decode defaults to CC000 (namely the low byte defaults to 67h).
Below chart shows the decoding of I/O Base Address 300h:
相關PDF資料
PDF描述
LAN91C96IQFP NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LAN91C96ITQFP NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LANF72351D ETHERNET 10BASE-T LAN FILTER MODULES
LANF7236G ETHERNET 10BASE-T LAN FILTER MODULES
LANF72761 ETHERNET 10BASE-T PCMCIA TRANSFORMER MODULES
相關代理商/技術參數
參數描述
LAN91C96IQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96ITQFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96-MS 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96-MU 功能描述:以太網 IC Ethernet IC 10Mbps MAC PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN91C96QFP 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*