- 您現在的位置：買賣IC網 > PDF目錄358742 > LAN91C96(100TQFP) LAN Node Controller PDF資料下載
參數資料
| 型號： | LAN91C96(100TQFP) |
| 英文描述： | LAN Node Controller |
| 中文描述： | 網絡節點控制器 |
| 文件頁數： | 28/55頁 |
| 文件大?。?/td> | 482K |
| 代理商： | LAN91C96(100TQFP) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
FEAST Fast Ethernet Controller
for PCMCIA and Generic 16-Bit Applications
SMSC DS – LAN91C110 REV. B
Page 28
Rev. 09/05/02
BANK 2
OFFSET
6
NAME
TYPE
SYMBOL
PTR
POINTER REGISTER
READ/WRITE
NOT EMPTY is a read
only bit
HIGH
BYTE
RCV
AUTO
INCR.
READ
ETEN
NOT
EMPTY
POINTER HIGH
0
0
0
0
0
0
0
0
LOW
BYTE
POINTER LOW
0
0
0
0
0
0
0
0
POINTER REGISTER - The value of this register determines the address to be accessed within the transmit or receive
areas. It will auto-increment on accesses to the data register when AUTO INCR. is set. The increment is by one for every
byte access, by two for every word access, and by four for every double word access. When RCV is set the address
refers to the receive area and uses the output of RX FIFO as the packet number, when RCV is clear the address refers to
the transmit area and uses the packet number at the Packet Number Register.
READ - Determines the type of access to follow. If the READ bit is high the operation intended is a read. If the READ bit is
low the operation is a write. Loading a new pointer value, with the READ bit high, generates a pre-fetch into the Data
Register for read purposes.
Readback of the pointer will indicate the value of the address last accessed by the CPU (rather than the last pre-fetched).
This allows any interrupt routine that uses the pointer, to save it and restore it without affecting the process being
interrupted. The Pointer Register should not be loaded until the Data Register FIFO is empty. The NOT EMPTY bit of this
register can be read to determine if the FIFO is empty. On reads, if IOCHRDY is not connected to the host, the Data Register
(ARDY) should not be read before 370ns after the pointer was loaded to allow the Data Register FIFO to fill.
If the pointer is loaded using 8 bit writes, the low byte should be loaded first and the high byte last.
ETEN - When set enables EARLY Transmit underrun detection. Normal operation when clear.
NOT EMPTY - When set indicates that the Write Data FIFO is not empty yet. The CPU can verify that the FIFO is empty
before loading a new pointer value. This is a read only bit.
Note:
If AUTO INCR. is not set, the pointer must be loaded with a dword aligned value.
BANK 2
OFFSET
NAME
8 THROUGH Bh
DATA REGISTER
TYPE
SYMBOL
DATA
READ/WRITE
DATA HIGH
X
X
X
X
X
X
X
X
DATA LOW
X
X
X
X
X
X
X
X
相關PDF資料 |
PDF描述 |
|---|---|
| LAN91C96(100QFP) | LAN Node Controller |
| LAN91C95 | LAN Node Controller |
| LAN91C100FD(208TQFP) | LAN Node Controller |
| LAN91C100FD(208PQFP) | LAN Node Controller |
| LAN91C94 | ISA/PCMCIA SINGLE CHIP ETHERNET CONTROLLER WITH RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN91C96I | 制造商:SMSC 制造商全稱:SMSC 功能描述:NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER |
| LAN91C96I_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:Non-PCI Single-Chip Full Duplex Ethernet Controller |
| LAN91C96IMS | 制造商:Microchip Technology Inc 功能描述: |
| LAN91C96I-MS | 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN91C96I-MU | 功能描述:以太網 IC Non-PCI 10 Mbps Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。