- 您現在的位置：買賣IC網 > PDF目錄359605 > LAN8187I (SMSC Corporation) High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX PDF資料下載
參數資料
| 型號： | LAN8187I |
| 廠商： | SMSC Corporation |
| 英文描述： | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| 中文描述： | 高性能信息產業部及RMII 10/100以太網PHY與HP Auto - MDIX功能 |
| 文件頁數： | 25/66頁 |
| 文件大?。?/td> | 545K |
| 代理商： | LAN8187I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX
Datasheet
4.5.4
SMSC LAN8187/LAN8187I
25
Revision 0.6 (02-24-06)
DATASHEET
Jabber Detection
Jabber is a condition in which a station transmits for a period of time longer than the maximum
permissible packet length, usually due to a fault condition, that results in holding the TX_EN input for
a long period. Special logic is used to detect the jabber state and abort the transmission to the line,
within 45ms. Once TX_EN is deasserted, the logic resets the jabber condition.
As shown in
Table 5.31
, bit 1.1 indicates that a jabber condition was detected.
4.6
MAC Interface
The MII/RMII block is responsible for the communication with the controller. Special sets of hand-shake
signals are used to indicate that valid received/transmitted data is present on the 4 bit receive/transmit
bus.
The device must be configured in MII or RMII mode. This is done by specific pin strapping
configurations.
See section
Section 4.6.3, "MII vs. RMII Configuration," on page 26
for information on pin strapping
and how the pins are mapped differently.
4.6.1
MII
The MII includes 16 interface signals:
transmit data - TXD[3:0]
transmit strobe - TX_EN
transmit clock - TX_CLK
transmit error - TX_ER/TXD4
receive data - RXD[3:0]
receive strobe - RX_DV
receive clock - RX_CLK
receive error - RX_ER/RXD4
collision indication - COL
carrier sense - CRS
In MII mode, on the transmit path, the PHY drives the transmit clock, TX_CLK, to the controller. The
controller synchronizes the transmit data to the rising edge of TX_CLK. The controller drives TX_EN
high to indicate valid transmit data. The controller drives TX_ER high when a transmit error is detected.
On the receive path, the PHY drives both the receive data, RXD[3:0], and the RX_CLK signal. The
controller clocks in the receive data on the rising edge of RX_CLK when the PHY drives RX_DV high.
The PHY drives RX_ER high when a receive error is detected.
4.6.2
RMII
The SMSC LAN8187/LAN8187I supports the low pin count Reduced Media Independent Interface
(RMII) intended for use between Ethernet PHYs and Switch ASICs. Under IEEE 802.3, an MII
comprised of 16 pins for data and control is defined. In devices incorporating many MACs or PHY
interfaces such as switches, the number of pins can add significant cost as the port counts increase.
The management interface (MDIO/MDC) is identical to MII. The RMII interface has the following
characteristics:
It is capable of supporting 10Mb/s and 100Mb/s data rates
A single clock reference is sourced from the MAC to PHY (or from an external source)
It provides independent 2 bit wide (di-bit) transmit and receive data paths
相關PDF資料 |
PDF描述 |
|---|---|
| LAN8187I-JT | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN8187-JT | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LPC47S42X | ENHANCED SUPER I/O WITH LPC INTERFACE FOR SERVER APPLICATIONS |
| LPC47M141-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M142-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN8187I-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN8187-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN83C171 | 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller |
| LAN83C171 WAF | 制造商:SMSC 功能描述: |
| LAN83C171QFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。