- 您現在的位置：買賣IC網 > PDF目錄10795 > KSZ9021RNI (Micrel Inc)IC TXRX 10/100/1000 SGL 48QFN PDF資料下載
參數資料
| 型號： | KSZ9021RNI |
| 廠商： | Micrel Inc |
| 文件頁數： | 36/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX 10/100/1000 SGL 48QFN |
| 標準包裝： | 260 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 8/8 |
| 規程： | 千兆位以太網 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN（7x7） |
| 包裝： | 托盤 |
| 配用： | 576-3874-ND - BOARD EVALUATION FOR KSZ9021RN |
| 其它名稱： | 576-3978 KSZ9021RNI-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2010 Microchip Technology Inc.
DS22265A-page 41
MCP444X/446X
4.0
FUNCTIONAL OVERVIEW
This Data Sheet covers a family of four nonvolatile Dig-
ital Potentiometer and Rheostat devices that will be
referred to as MCP44XX. The MCP44X1 devices are
the Potentiometer configuration, while the MCP44X2
devices are the Rheostat configuration.
As the Device Block Diagram shows, there are four
main functional blocks. These are:
The POR/BOR operation and the Memory Map are
discussed in this section and the Resistor Network and
I2C operation are described in their own sections. The
commands are discussed in
4.1
POR/BOR and RESET Operation
The Power-on Reset is the case where the device is
having power applied to it from VSS. The Brown-out
Reset occurs when a device had power applied to it,
and that power (voltage) drops below the specified
range.
The devices RAM retention voltage (VRAM) is lower
than the POR/BOR voltage trip point (VPOR/VBOR). The
maximum VPOR/VBOR voltage is less then 1.8V.
When VPOR/VBOR < VDD < 2.7V, the electrical
performance
may
not
meet
the
data
sheet
specifications. In this region, the device is capable of
reading and writing to its EEPROM and incrementing,
decrementing, reading and writing to its volatile
memory if the proper serial command is executed.
When VDD < VPOR/VBOR or the RESET pin is Low, the
pin weak pull-ups are enabled.
4.1.1
POWER-ON RESET
When the device powers up, the device VDD will cross
the VPOR/VBOR voltage. Once the VDD voltage crosses
the VPOR/VBOR voltage, the following happens:
The volatile wiper register is loaded with value in
the corresponding nonvolatile wiper register
The TCON registers are loaded with their default
value
The device is capable of digital operation
4.1.2
BROWN-OUT RESET
When the device powers down, the device VDD will
cross the VPOR/VBOR voltage.
Once the VDD voltage decreases below the VPOR/VBOR
voltage, the following happens:
Serial Interface is disabled
EEPROM Writes are disabled
If the VDD voltage decreases below the VRAM voltage,
the following happens:
Volatile wiper registers may become corrupted
TCON registers may become corrupted
As the voltage recovers above the VPOR/VBOR voltage,
Serial commands not completed due to a brown-out
condition may cause the memory location (volatile and
nonvolatile) to become corrupted.
4.1.3
RESET PIN
The RESET pin can be used to force the device into
the POR/BOR state of the device. When the RESET
pin is forced Low, the device is forced into the reset
state. This means that the TCON and STATUS
registers are forced to their default values and the
volatile wiper registers are loaded with the value in the
corresponding Nonvolatile wiper register. Also the I2C
interface is disabled. Any nonvolatile write cycle is not
interrupted, and allowed to complete.
This feature allows a hardware method for all registers
to be updated at the same time.
4.1.4
INTERACTION OF RESET PIN AND
BOR/POR CIRCUITRY
Figure 4-1 shows how the RESET pin signal and the
POR/BOR signal interact to control the hardware reset
state of the device.
FIGURE 4-1:
POR/BOR Signal and
RESET Pin Interaction.
RESET (from pin)
POR/BOR signal
Device reset
相關PDF資料 |
PDF描述 |
|---|---|
| AD7849AR-REEL | IC DAC 16BIT SRL INP 20-SOIC |
| JBXEA2G07FCSDS | CONN RCPT 7POS DOUBLE NUT CRIMP |
| LTC1382CSW#PBF | IC TXRX 5V RS232 W/SHTDWN 18SOIC |
| AD7549KP | IC DAC 12BIT DUAL LC2MOS 20-PLCC |
| LTC1843IS8#PBF | IC COMP ULTLOPWR W/REF DL 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ9031MNX | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:The KSZ9031MNX is a completely integrated triple-speed (10Base-T/100Base-TX/1000Base-T) Ethernet physicallayer transceiver for transmission and reception of data on standard CAT-5 unshielded twisted pair (UTP) cable. |
| KSZ9031MNXCA | 功能描述:以太網 IC 1-Port Gigabit Ethernet PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ9031MNXCA TR | 功能描述:以太網 IC 1-Port Gigabit Ethernet PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ9031MNXCA-TR | 功能描述:4/4 Transceiver Full Ethernet 64-QFN (8x8) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:收發器 協議:以太網 驅動器/接收器數:4/4 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-VFQFN 裸露焊盤 供應商器件封裝:64-QFN（8x8） 標準包裝:1 |
| KSZ9031MNXCC | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:The KSZ9031MNX is a completely integrated triple-speed (10Base-T/100Base-TX/1000Base-T) Ethernet physicallayer transceiver for transmission and reception of data on standard CAT-5 unshielded twisted pair (UTP) cable. |
發布緊急采購，3分鐘左右您將得到回復。