參數資料
型號： KSZ8895MQ
廠商： Micrel Inc
文件頁數： 62/119頁
文件大?。?/td> 0K
描述： IC ETHERNET SW 5PORT 128-PQFP
標準包裝： 66
控制器類型： 以太網開關控制器
接口： MII
電源電壓： 1.8V，2.5V，3.3V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
配用： 576-3871-ND - BOARD EVALUATION FOR KSZ8895MQ
其它名稱： 576-3753
Micrel, Inc.
KSZ8895MQ/RQ/FMQ
DA found in
Static MAC table
USE FID
Flag?
FID Match?
DA+FID found in
Dynamic MAC table
Action
No
Do Not care
No
Broadcast to the membership ports defined in
the VLAN table bit[11:7].
No
Do Not care
Yes
Send to the destination port defined in the
dynamic MAC table bit[58:56].
Yes
0
Do Not care
Send to the destination port(s) defined in the
static MAC table bit[52:48].
Yes
1
No
Broadcast to the membership ports defined in
the VLAN table bit[11:7].
Yes
1
No
Yes
Send to the destination port defined in the
dynamic MAC table bit[58:56].
Yes
1
Yes
Do Not care
Send to the destination port(s) defined in the
static MAC table bit[52:48].
Table 8. FID+DA Look-Up in the VLAN Mode
SA+FID found in
Dynamic MAC table
Action
No
The SA+FID will be learned into the dynamic table.
Yes
Time stamp will be updated.
Table 9. FID+SA Look-Up in the VLAN Mode
Advanced VLAN features are also supported in KSZ8895MQ/RQ/FMQ, such as “VLAN ingress filtering” and “discard
non PVID” defined in bits [6:5] of the port Register Control 2. These features can be controlled on a port basis.
Rate Limiting Support
The KSZ8895MQ/RQ/FMQ provides a fine resolution hardware rate limiting. The rate step is 64Kbps when the rate
limit is less than 1Mbps rate for 100BT or 10BT. The rate step is 1Mbps when the rate limit is more than 1Mbps rate
for 100BT or 10BT (refer to Data Rate Selection Table which follow the end of the Port Register Queue 0
3
Ingress/Egress Limit Control section). The rate limit is independently on the “receive side” and on the “transmit side”
on a per port basis. For 10BASE-T, a rate setting above 10 Mbps means the rate is not limited. On the receive side,
the data receive rate for each priority at each port can be limited by setting up Ingress Rate Control Registers. On the
transmit side, the data transmit rate for each priority queue at each port can be limited by setting up Egress Rate
Control Registers. The size of each frame has options to include minimum IFG (Inter Frame Gap) or Preamble byte,
in addition to the data field (from packet DA to FCS).
Ingress Rate Limit
For ingress rate limiting, KSZ8895MQ/RQ/FMQ provides options to selectively choose frames from all types,
multicast, broadcast, and flooded unicast frames by bits [3
2] of the port rate limit control register. The
KSZ8895MQ/RQ/FMQ counts the data rate from those selected type of frames. Packets are dropped at the ingress
port when the data rate exceeds the specified rate limit or the flow control takes effect without packet dropped when
the ingress rate limit flow control is enabled by the port rate limit control register bit 4. The ingress rate limiting
supports the port-based, 802.1p and DiffServ-based priorities, the port-based priority is fixed priority 0
3 selection by
bits [4-3] of the port register control 0. The 802.1p and DiffServ-based priority can be mapped to priority 0
3 by
default of the register 128 and 129. In the ingress rate limit, set register 135 global control 19 bit 3 to enable queue-
based rate limit if using two-queue or four-queue mode. All related ingress ports and egress port should be split to
two-queue or four-queue mode by the port registers control 9 and control 0. The four-queue mode will use Q0
Q3 for
priority 0
3 by bit[60] of the port register ingress limit control 14. The two-queue mode will use Q0Q1 for priority
0-1by bit[6-0] of the port register ingress limit control 1
2. The priority levels in the packets of the 802.1p and DiffServ
can be programmed to priority 0
3 by the register 128 and 129 for a re-mapping.
March 12, 2014
47
Revision 1.7
相關PDF資料
PDF描述
KSZ8993FL IC CONV MED 10/100 SGL 128PQFP
KSZ8993MLI IC SWITCH 10/100 3PORT 128-PQFP
KSZ8993ML IC SWITCH 10/100 W/TXRX 128PQFP
KSZ8995FQ IC SWITCH 10/100 5PORT 128-PQFP
KSZ8995MA IC SWITCH 10/100 5PORT 128PQFP
相關代理商/技術參數
參數描述
KSZ8895MQ_12 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 5-Port 10/100 Managed Ethernet Switch with MII/RMII interface
KSZ8895MQ-EVAL 功能描述:以太網開發工具 5-Port 10/100 Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8895MQI 功能描述:以太網 IC 5-Port 10/100 Ethernet Switch with 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8895MQXCA 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:0°C ~ 70°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66
KSZ8895MQXIA 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:-40°C ~ 85°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*