- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8895MQ (Micrel Inc)IC ETHERNET SW 5PORT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8895MQ |
| 廠商： | Micrel Inc |
| 文件頁數： | 51/119頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ETHERNET SW 5PORT 128-PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-3871-ND - BOARD EVALUATION FOR KSZ8895MQ |
| 其它名稱： | 576-3753 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
Micrel, Inc.
KSZ8895MQ/RQ/FMQ
The KSZ8895MQ/RQ/FMQ will not forward the following packets:
1.
Error packets
These include framing errors, Frame Check Sequence (FCS) errors, alignment errors, and illegal size packet
errors.
2.
IEEE802.3x PAUSE frames
KSZ8895MQ/RQ/FMQ intercepts these packets and performs full duplex flow control accordingly.
3.
"Local" packets
Based on destination address (DA) lookup, if the destination port from the lookup table matches the port from
which the packet originated, the packet is defined as "local."
Half-Duplex Back Pressure
The KSZ8895MQ/RQ/FMQ also provides a half-duplex back pressure option (note: this is not in IEEE 802.3
standards). The activation and deactivation conditions are the same as the ones given for full-duplex mode. If back
pressure is required, the KSZ8895MQ/RQ/FMQ sends preambles to defer the other station's transmission (carrier
sense deference). To avoid jabber and excessive deference as defined in IEEE 802.3 standards, after a certain
period of time, the KSZ8895MQ/RQ/FMQ discontinues carrier sense but raises it quickly after it drops packets to
inhibit other transmissions. This short silent time (no carrier sense) is to prevent other stations from sending out
packets and keeps other stations in a carrier sense-deferred state. If the port has packets to send during a back
pressure situation, the carrier sense-type back pressure is interrupted and those packets are transmitted instead. If
there are no more packets to send, carrier sense-type back pressure becomes active again until switch resources
are free. If a collision occurs, the binary exponential backoff algorithm is skipped and carrier sense is generated
immediately, reducing the chance of further colliding and maintaining carrier sense to prevent reception of packets.
To ensure no packet loss in 10BASE-T or 100BASE-TX half-duplex modes, the user must enable the following:
Aggressive backoff (Register 3, bit 0)
No excessive collision drop (Register 4, bit 3)
Back pressure (Register 4, bit 5)
These bits are not set as the default because this is not the IEEE standard.
Broadcast Storm Protection
The KSZ8895MQ/RQ/FMQ has an intelligent option to protect the switch system from receiving too many broadcast
packets. Broadcast packets are normally forwarded to all ports except the source port and thus use too many switch
resources (bandwidth and available space in transmit queues). The KSZ8895MQ/RQ/FMQ has the option to include
“multicast packets” for storm control. The broadcast storm rate parameters are programmed globally and can be
enabled or disabled on a per port basis. The rate is based on a 50ms (0.05s) interval for 100BT and a 500ms (0.5s)
interval for 10BT. At the beginning of each interval, the counter is cleared to zero and the rate limit mechanism starts
to count the number of bytes during the interval. The rate definition is described in Registers 6 and 7. The default
setting for Registers 6 and 7 is 0x4A (74 decimal). This is equal to a rate of 1%, calculated as follows:
148,80 frames/sec X 50ms (0.05s)/interval X 1% = 74 frames/interval (approx.) = 0x4A
March 12, 2014
37
Revision 1.7
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
| KSZ8995FQ | IC SWITCH 10/100 5PORT 128-PQFP |
| KSZ8995MA | IC SWITCH 10/100 5PORT 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8895MQ_12 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 5-Port 10/100 Managed Ethernet Switch with MII/RMII interface |
| KSZ8895MQ-EVAL | 功能描述:以太網開發工具 5-Port 10/100 Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8895MQI | 功能描述:以太網 IC 5-Port 10/100 Ethernet Switch with 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8895MQXCA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:0°C ~ 70°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
| KSZ8895MQXIA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:-40°C ~ 85°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
發布緊急采購，3分鐘左右您將得到回復。