- 您現在的位置：買賣IC網 > PDF目錄10817 > KSZ8051MLL (Micrel Inc)TXRX PHY 10/T100 3.3V MII 48LQFP PDF資料下載
參數資料
| 型號： | KSZ8051MLL |
| 廠商： | Micrel Inc |
| 文件頁數： | 35/48頁 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 10/T100 3.3V MII 48LQFP |
| 特色產品： | KSZ8051MLL Physical Layer Transceiver KSZ8051/8031/8021 Series |
| 標準包裝： | 250 |
| 類型： | PHY 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 配用： | 576-3864-ND - BOARD EVALUATION FOR KSZ8051MLL |
| 其它名稱： | 576-3731 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
2008 Microchip Technology Inc.
DS22060B-page 43
MCP413X/415X/423X/425X
6.1.4
SERIAL CLOCK (SCK)
(SPI FREQUENCY OF OPERATION)
The SPI interface is specified to operate up to 10 MHz.
The actual clock rate depends on the configuration of
the system and the serial command used. Table 6-1
shows the SCK frequency for different configurations.
TABLE 6-1:
SCK FREQUENCY
6.1.5
THE CS SIGNAL
The Chip Select (CS) signal is used to select the device
and frame a command sequence. To start a command,
or sequence of commands, the CS signal must
transition from the inactive state (VIH) to an active state
(VIL or VIHH).
After the CS signal has gone active, the SDO pin is
driven and the clock bit counter is reset.
If an error condition occurs for an SPI command, then
the Command byte’s Command Error (CMDERR) bit
(on the SDO pin) will be driven low (VIL). To exit the
error condition, the user must take the CS pin to the VIH
level.
When the CS pin returns to the inactive state (VIH) the
SPI module resets (including the address pointer).
While the CS pin is in the inactive state (VIH), the serial
interface is ignored. This allows the Host Controller to
interface to other SPI devices using the same SDI,
SDO, and SCK signals.
The CS pin has an internal pull-up resistor. The resistor
is disabled when the voltage on the CS pin is at the VIL
level. This means that when the CS pin is not driven,
the internal pull-up resistor will pull this signal to the VIH
level.
When the CS pin is driven low (VIL), the
resistance becomes very large to reduce the device
current consumption.
The high voltage capability of the CS pin allows
MCP413X/415X/423X/425X devices to be used in
systems previously designed for the MCP414X/416X/
424X/426X devices.
Memory Type Access
Command
Read
Write,
Increment,
Decrement
Volatile
Memory
SDI, SDO
10 MHz
SDI/SDO(1) 250 kHz (2)
10 MHz
Note 1: MCP41X1 devices only.
2: This is the maximum clock frequency
without an external pull-up resistor.
Note:
There is a required delay after the CS pin
goes active to the 1st edge of the SCK pin.
相關PDF資料 |
PDF描述 |
|---|---|
| JKXFD1G05MSSDSR | CONN PLUG 5POS CABLE STR SOLDER |
| SP483CN-L | IC TXRX RS485 HALF DUPLEX 8NSOIC |
| ADM3101EACPZ-250R7 | IC TXRX RS-232 3.3V 15KV 12LFCSP |
| MX7534KN+ | IC DAC 14BIT MPU COMP 20-DIP |
| SP485RCP-L | IC TXRX RS485 HALF DUPLEX 8PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8051MLL TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (48-LQFP) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051MLL-EVAL | 功能描述:以太網開發工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (48-LQFP) - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8051MLLI | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (48-LQFP, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051MLLI TR | 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (48-LQFP, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8051MLLI-TR | 功能描述:1/1 Transceiver Full MII 48-LQFP (7x7) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:MII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商器件封裝:48-LQFP（7x7） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。