- 您現在的位置：買賣IC網 > PDF目錄373153 > KM4101IT6TR3 (FAIRCHILD SEMICONDUCTOR CORP) Low Cost, +2.7V and +5V, 260MHz Rail-to-Rail Amplifiers PDF資料下載
參數資料
| 型號： | KM4101IT6TR3 |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low Cost, +2.7V and +5V, 260MHz Rail-to-Rail Amplifiers |
| 中文描述： | OP-AMP, 8000 uV OFFSET-MAX, 86 MHz BAND WIDTH, PDSO6 |
| 封裝： | SOT-23, 6 PIN |
| 文件頁數： | 8/11頁 |
| 文件大小： | 333K |
| 代理商： | KM4101IT6TR3 |
8
REV. 1A February 2001
Figure 4: Overdrive Recovery
Driving Capacitive Loads
The Frequency Response vs. C
L
plot on page 4,
illustrates the response of the KM4100 and KM4101. A
small series resistance (R
s
) at the output of the amplifier,
illustrated in Figure 5, will improve stability and
settling performance. R
s
values in the Frequency
Response vs. C
L
plot were chosen to achieve maximum
bandwidth with less than 1dB of peaking. For maximum
flatness, use a larger R
s
.
Figure 5: Typical Topology for driving
a capacitive load
Layout Considerations
General layout and supply bypassing play major roles
in high frequency performance. Fairchild has evaluation
boards to use as a guide for high frequency layout
and to aid in device testing and characterization.
Follow the steps below as a basis for high frequency
layout:
I
Include 6.8
μ
F and 0.01
μ
F ceramic capacitors
I
Place the 6.8
μ
F capacitor within 0.75 inches
of the power pin
I
Place the 0.01
μ
F capacitor within 0.1 inches
of the power pin
I
Remove the ground plane under and around the
part, especially near the input and output pins to
reduce parasitic capacitance
I
Minimize all trace lengths to reduce
series inductances
Refer to the evaluation board layouts shown in Figure
7 for more information.
Evaluation Board Information
The following evaluation boards are available to aid
in the testing and layout of this device:
Evaluation board schematics and layouts are shown in
Figure 6 and Figure 7.
The KEB002 and KEB003 evaluation boards are built
for dual supply operation. Follow these steps to use
the board in a single supply application:
1. Short -V
s
to ground
2. Use C3 and C4, if the -V
s
pin of the KM4100 or
KM4101 is not directly connected to the
ground plane.
Figure 6: Evaluation Board Schematic
(SOIC pinout shown)
Overdrive Recovery
I
Time (20ns/div)
Output
Input
R
L
= 2k
V
=2V
pp
G = 5
R
f
= 1k
+
-
R
f
R
g
R
s
C
L
R
L
Eval Board
KEB002
Description
Products
KM4100IT5,
Single Channel,
Dual Supply 5 & 6 lead SOT23 KM4101IT6
Single Channel, Dual Supply
8 lead SOIC
KEB003
KM4100IC8,
KM4101IC8
DATA SHEET
KM4100/KM4101
相關PDF資料 |
PDF描述 |
|---|---|
| KM4132G271AQ-10 | 128K x 32Bit x 2 Banks Synchronous Graphic RAM |
| KM4132G271A-10 | 128K x 32Bit x 2 Banks Synchronous Graphic RAM |
| KM4132G271A-12 | 128K x 32Bit x 2 Banks Synchronous Graphic RAM |
| KM4132G271A-8 | 128K x 32Bit x 2 Banks Synchronous Graphic RAM |
| KM4132G271A | 128K x 32Bit x 2 Banks Synchronous Graphic RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KM4110 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:0.5mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers |
| KM4110IT5 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:0.5mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers |
| KM4110IT5TR3 | 功能描述:運算放大器 - 運放 0.5ma 75Mhz RRO amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| KM4111 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amplifiers |
| KM4111IT5TR3 | 功能描述:高速運算放大器 0.2ma 35Mhz RRO amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。