- 您現在的位置：買賣IC網 > PDF目錄15796 > KIT33298DWEVB (Freescale Semiconductor)KIT EVAL FOR MC33298 SMART SW PDF資料下載
參數資料
| 型號： | KIT33298DWEVB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 5/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL FOR MC33298 SMART SW |
| 標準包裝： | 1 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
33298
FUNCTIONAL DESCRIPTION
INTRODUCTION
ARCHIVE
INFORMATION
ARCHIVE
INFORMATION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33298 was conceived, specified, designed, and
developed for automotive applications. It is an eight output
low side power switch having 8-bit serial control. The 33298
incorporates SMARTMOS
technology having effective 1.5
CMOS logic, bipolar/MOS analog circuitry, and independent
state of the art double diffused MOS (DMOS) power output
transistors. Many benefits are realized as a direct result of
using this mixed technology. A simplified block diagram
delineates 33298 in Figure 1.
Where bipolar devices require considerable control
current for their operation, structured MOS devices, since
they are voltage controlled, require only transient gate
charging current affording a significant decrease in power
consumption. The CMOS capability of the SMARTMOS
process allows significant amounts of logic to be
economically incorporated into the monolithic design.
Additionally, the bipolar/MOS analog circuits embedded
within the updrain power DMOS output transistors monitor
and provide fast, independent protection control functions for
each individual output. All outputs have internal 65V at 0.5A
independent output voltage clamps to provide fast inductive
turn-off and transient protection.
The 33298 uses high efficiency updrain power DMOS
output transistors exhibiting very low room temperature
drain-to-source ON resistance values (RDS(on) ≤ 1.0Ω at 13V
VPWR) and dense CMOS control logic. Operational bias
currents of less than 2.0mA (1.0mA typical) with any
combination of outputs ON are the result of using this mixed
technology and would not be possible with bipolar structures.
To accomplish a comparable functional feature set using a
bipolar structure approach, would result in a device requiring
hundreds of milliamperes of internal bias and control current.
This would represent a very large amount of power to be
consumed by the device itself and not available for load use.
During operation, the 33298 functions as an eight output
serial switch serving as a microcontroller (MCU) bus
expander and buffer, with fault management and fault
reporting features.
In doing so, the device directly relieves the MCU of the
fault management functions.
The 33298 directly relieves the MCU of the fault
management functions. The 33298 directly interfaces to an
MCU, operating at system clock serial frequencies in excess
of 3.0MHz. It uses a Synchronous Peripheral Interface (SPI)
for control and diagnostic readout. Figure 13 illustrates the
basic SPI configuration between an MCU and one 33298.
Figure 13. SPI Interface with Microcontroller
The circuit can also be used in a variety of other
applications in the computer, telecommunications, and
industrial fields. It is parametrically specified over an input
battery /supply range of 9.0 to 16V but is designed to operate
over a considerably wider range of 5.5 to 26.5V. The design
incorporates the use of Logic Level MOSFETs as output
devices. These MOSFETs are sufficiently turned ON with a
gate voltage of less than 5.0V thus eliminating the need for
an internal charge pump. Each output is identically sized and
independent in operation. The efficiency of each output
transistor, at room temperature provides as little as 9.0V
supply (VPWR), the maximum RDS(on) of an output
All inputs are compatible with 5.0V CMOS logic levels,
incorporating negative or inverted logic. Whenever an input is
programmed to a logic low state (<1.0V) the corresponding
low side switched output being controlled will be active low
and turned ON. Conversely, whenever an input is
programmed to a logic high state (>3.0V), the output being
controlled will be high and turned OFF.
33298
MC68HCXX
Microcontroller
Shift Register
To
Logic
Receive
Buffer
Parallel
Ports
MOSI
SI
MISO
SO
SCLK
RST
CS
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B5J-EW-S | CONVERTER MOD DC/DC 36V 100W |
| 5800-562-RC | CHOKE RF HI CURRENT 5600UH .082A |
| VI-B5H-EY-F4 | CONVERTER MOD DC/DC 52V 50W |
| GSC18DRXS-S734 | CONN EDGECARD 36POS DIP .100 SLD |
| HBM18DSUS | CONN EDGECARD 36POS .156 DIP SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KIT33394DWBEVB | 功能描述:KIT EVAL FOR MC33394 8X PWR SPLY RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| KIT33660EFEVBE | 功能描述:界面開發工具 ISO K LINE SERIAL LINK I RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| KIT33661DEVB | 功能描述:網絡開發工具 ELIN TRANSCEIVER RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| KIT33662JEFEVBE | 功能描述:界面開發工具 LIN 2.1 / SAEJ2602-2 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| KIT33662LEFEVBE | 功能描述:界面開發工具 LIN 2.1 / SAEJ2602-2 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。