- 您現在的位置：買賣IC網 > PDF目錄10503 > ISLA212P13IRZ (Intersil)IC ADC 12BIT SRL/SPI 72QFN PDF資料下載
參數資料
| 型號： | ISLA212P13IRZ |
| 廠商： | Intersil |
| 文件頁數： | 21/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT SRL/SPI 72QFN |
| 標準包裝： | 1 |
| 系列： | FemtoCharge™ |
| 位數： | 12 |
| 采樣率（每秒）： | 130M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 414mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 72-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 72-QFN（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ISLA212P
28
FN7717.2
November 30, 2012
field [7:4] at 0xC0 or user defined patterns by writing to the user
test mode field [2:0] at 0xC0. The user defined patterns should
be loaded at address space 0xC1 through 0xD0, see the “SPI
Memory Map” on page 30 for more detail. The predefined
patterns are shown in Table 13. The test mode is enabled
asynchronously to the sample clock, therefore several sample
clock cycles may elapse before the data is present on the output
bus.
ADDRESS 0XC0: TEST_IO
Bits 7:4 Output Test Mode
These bits set the test mode according to Table 13. Other values
are reserved. User test patterns loaded at 0xC1 through 0xD0 are
also available by writing ‘1000’ to [7:4] at 0xC0 and a pattern
depth value to [2:0] at 0xC0. See “SPI Memory Map” on page 30.
Bits 2:0 User Test Mode
The three LSBs in this register determine the test pattern in
combination with registers 0xC1 through 0xD0. Refer to the
SPI Memory Map on page 30.
ADDRESS 0XC1: USER_PATT1_LSB
ADDRESS 0XC2: USER_PATT1_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 1.
ADDRESS 0XC3: USER_PATT2_LSB
ADDRESS 0XC4: USER_PATT2_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 2
ADDRESS 0XC5: USER_PATT3_LSB
ADDRESS 0XC6: USER_PATT3_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 3
ADDRESS 0XC7: USER_PATT4_LSB
ADDRESS 0XC8: USER_PATT4_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 4.
ADDRESS 0XC9: USER_PATT5_LSB
ADDRESS 0XCA: USER_PATT5_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 5.
ADDRESS 0XCB: USER_PATT6_LSB
ADDRESS 0XCC: USER_PATT6_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 6.
ADDRESS 0XCD: USER_PATT7_LSB
ADDRESS 0XCE: USER_PATT7_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 7.
ADDRESS 0XCF: USER_PATT8_LSB
ADDRESS 0XD0: USER_PATT8_MSB
These registers define the lower and upper eight bits,
respectively, of the user-defined pattern 8.
ADDRESS 0XFE: OFFSET/GAIN_ADJUST_ENABLE
Bit 0 at this register must be set high to enable adjustment of
offset coarse and fine adjustments (0x20 and 0x21), and gain
medium and fine adjustments (0x23 and 0x24). It is
recommended that new data be written to the offset and gain
adjustment registers and while Bit 0 is a '0'. Subsequently, Bit 0
should be set to '1' to allow the values written to the
aforementioned registers to be used by the ADC. Bit 0 should be
set to a '0' upon completion.
Digital Temperature Sensor
ADDRESS 0X4B: TEMP_COUNTER_HIGH
Bits [2:0] of this register hold the 3 MSBs of the 11-bit
temperature code.
Bit [7] of this register indicates a valid temperature_counter read
was performed. A logic ‘1’ indicates a valid read.
ADDRESS 0X4C: TEMP_COUNTER_LOW
Bits [7:0] of this register hold the lower 8 LSBs of the 11-bit
temperature code.
TABLE 13. OUTPUT TEST MODES
VALUE
0xC0[7:4]
OUTPUT TEST MODE
WORD 1
WORD 2
0000
Off
0001
Midscale
0x8000
N/A
0010
Positive Full-Scale
0xFFFF
N/A
0011
Negative Full-Scale
0x0000
N/A
0100
SDR/DDR Dependent
N/A
0101
Reserved
N/A
0110
Reserved
N/A
0111
SDR/DDR Dependent
N/A
1000
User Pattern
user_patt1
user_patt2
1001
Reserved
N/A
1010
Ramp
N/A
相關PDF資料 |
PDF描述 |
|---|---|
| MAX204CPE+ | IC TRANSCEIVER RS232 5V 16-DIP |
| MAX234CWE+ | IC 4DVR/0RCVR RS232 5V 16-SOIC |
| KAD5510P-17Q48 | IC ADC 10BIT CMOS 170MSPS 48QFN |
| MAX204CWE+ | IC TXRX RS-232 W/CAP 16-SOIC |
| HI3-574AJN-5Z | IC ADC 12BIT 40KSPS 28-PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISLA212P20 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:12-Bit, 500MSPS ADC Programmable Built-in Test Patterns |
| ISLA212P20IRZ | 功能描述:IC ADC 12BIT SRL/SPI 72QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:FemtoCharge™ 產品培訓模塊:Data Converter Basics 標準包裝:1,000 系列:- 位數:10 采樣率（每秒）:30M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:150mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極 配用:296-10003-ND - EVAL MOD FOR THS1030296-10004-ND - EVAL MOD FOR THS1031 |
| ISLA212P25 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:12-Bit, 500MSPS ADC Programmable Built-in Test Patterns |
| ISLA212P25IRZ | 制造商:Intersil Corporation 功能描述:12-BIT 250MSPS ADC, 72-PIN QFN - Trays 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SPI/SRL 250M 72QFN |
| ISLA212P50 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:12-Bit, 500MSPS ADC Programmable Built-in Test Patterns |
發布緊急采購，3分鐘左右您將得到回復。