- 您現在的位置：買賣IC網 > PDF目錄9378 > ISL12028IB27Z (Intersil)IC RTC W/EEPROM 2.7V 14SOIC PDF資料下載
參數資料
| 型號： | ISL12028IB27Z |
| 廠商： | Intersil |
| 文件頁數： | 18/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC W/EEPROM 2.7V 14SOIC |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，監控器，監視計時器 |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOICN |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
25
FN8233.9
November 30, 2010
Backup Battery Operation
Many types of batteries can be used with the Intersil RTC
products. 3.0V or 3.6V Lithium batteries are appropriate, and
sizes are available that can power a Intersil RTC device for up
to 10 years. Another option is to use a supercapacitor for
applications where VDD may disappear intermittently for short
periods of time. Depending on the value of supercapacitor
used, backup time can last from a few days to two weeks (with
>1F). A simple silicon or Schottky barrier diode can be used in
series with VDD to charge the supercapacitor, which is
connected to the VBAT pin. Try to use Schottky diodes with
very low leakages, <1A desirable. Do not use the diode to
charge a battery (especially lithium batteries!).
Note that whether a battery or supercap is used, if the VBAT
voltage drops below the data sheet minimum of 1.8V and the
VDD power cycles to 0V then back to VDD voltage, then the
RESET output may stay low and the I2C communications will
not operate. The VBAT and VDD power will need to be cycled
to 0V together to allow normal operation again.
There are two possible modes for battery backup operation,
Standard and Legacy mode. In Standard mode, there are no
operational concerns when switching over to battery backup
since all other devices functions are disabled. Battery drain
is minimal in Standard mode, and return to Normal VDD
powered operations predictable. In Legacy modes the VBAT
pin can power the chip if the voltage is above VDD and
VTRIP. This makes it possible to generate alarms and
communicate with the device under battery backup, but the
supply current drain is much higher than the Standard mode
and backup time is reduced. In this case if alarms are used
in backup mode, the IRQ/FOUT pull up resistor must be
connected to VBAT voltage source..
I2C Communications During Battery Backup and
LVR Operation
Operation in Battery Backup mode and LVR is affected by
the BSW and SBIB bits as described earlier. These bits allow
flexible operation of the serial bus and EEPROM in battery
backup mode, but certain operational details need to be
clear before utilizing the different modes. The most
significant detail is that once VDD goes below VRESET, then
I2C communications cease regardless of whether the device
is programmed for I2C operation in battery backup mode.
Table 11 describes 4 different modes possible with using the
BSW and SBIB bits, and how they are affect LVR and battery
backup operation.
Mode A - In this mode, selection bits indicate a low VDD
switchover combined with I2C operation in battery backup
mode. In actuality the VDD will go below VRESET before
switching to battery backup, which will disable I2C
ANYTIME the device goes into battery backup mode.
Regardless of the battery voltage, the I2C will work down
Mode B - In this mode, the selection bits indicate
switchover to battery backup at VDD<VBAT, and I
2C
communications in battery backup. In order to
communicate in battery backup mode, the VRESET voltage
must be less than the VBAT voltage AND VDD must be
greater than VRESET. Also, pull-ups on the I
2C-bus pins
must go to VBAT to communicate. This mode is the same
as the normal operating mode of the X1228 device
Mode C - In this mode, the selection bits indicate a low
VDD switchover combined with no communications in
battery backup. Operation is actually identical to Mode A
with I2C communications down to VDD = VRESET, then no
communications (see Figure 29).
Mode D - In this mode, the selection bits indicate
switchover to battery backup at VDD<VBAT, and no I
2C
communications in battery backup. This mode is unique in
that there is I2C communication as long as VDD is higher
than VRESET or VBAT, whichever is greater. This mode is
the safest for guaranteeing I2C communications only when
Note that the IRQ/FOUT CMOS output pin is active in battery
backup for all modes. This should be considered if the load
on this pin is powered down, and could draw current from
the PMOS transistor and drain the battery. If that is the case,
the designer should consider the ISL12029 device which has
an open-drain output and avoids excessive current draw in
battery backup.
FIGURE 28. SUPERCAPACITOR CHARGING CIRCUIT
VDD
VBAT
VSS
SUPERCAPACITOR
2.7V TO 5.5V
ISL12028, ISL12028A
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J7X-MZ | CONVERTER MOD DC/DC 5.2V 25W |
| ISL12028IB27Z-T | IC RTC/CALENDAR EEPROM 14-SOIC |
| VI-J7V-MZ | CONVERTER MOD DC/DC 5.8V 25W |
| VI-J7P-MZ | CONVERTER MOD DC/DC 13.8V 25W |
| ISL12028IBZ-T | IC RTC EEPROM LP 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL12028IB27Z-T | 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 2 7VSET 14 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12028IB30AZ | 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 3 09VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12028IB30AZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 3 09VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12028IBAZ | 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 4 64VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12028IBAZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 4 64VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。