- 您現在的位置：買賣IC網 > PDF目錄2001 > ISL12026IBZ-T7A (Intersil)IC RTC/CALENDAR EEPROM 8SOIC PDF資料下載
參數資料
| 型號： | ISL12026IBZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC/CALENDAR EEPROM 8SOIC |
| 標準包裝： | 250 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年 |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
15
FN8231.9
November 30, 2010
In the read mode, the device will transmit 8 bits of data,
release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no stop
condition is generated by the master, the device will continue
to transmit data. The device will terminate further data
transmissions if an acknowledge is not detected. The master
must then issue a stop condition to return the device to
Standby mode and place the device into a known state.
Device Addressing
Following a start condition, the master must output a Slave
Address Byte. The first 4 bits of the Slave Address Byte
specify access to either the EEPROM array or to the CCR.
Slave bits ‘1010’ access the EEPROM array. Slave bits
‘1101’ access the CCR.
When shipped from the factory, EEPROM array is
UNDEFINED, and should be programmed by the customer
to a known state.
Bit 3 through Bit 1 of the slave byte specifies the device
select bits. These are set to ‘111’.
The last bit of the Slave Address Byte defines the operation
to be performed. When this R/W bit is a one, then a read
operation is selected. A zero selects a write operation
(see Figure 15).
After loading the entire Slave Address Byte from the SDA
bus, the ISL12026 compares the device identifier and device
select bits with ‘1010111’ or ‘1101111’. Upon a correct
compare, the device outputs an acknowledge on the SDA
line.
SCL
SDA
DATA STABLE
DATA CHANGE
DATA STABLE
FIGURE 12. VALID DATA CHANGES ON THE SDA BUS
SCL
SDA
START
STOP
FIGURE 13. VALID START AND STOP CONDITIONS
SCL FROM
MASTER
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
8
1
9
START
ACKNOWLEDGE
FIGURE 14. ACKNOWLEDGE RESPONSE FROM RECEIVER
ISL12026, ISL12026A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL12027IV27AZ | IC RTC/CALENDAR EEPROM 8-TSSOP |
| ISL12028IVZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
| ISL12029IVZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
| ISL12030IBZ | IC RTC/CALENDAR EEPROM 8-SOIC |
| ISL12032IVZ | IC RTC LP BATT BACK SRAM 14TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL12026IVZ | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12026IVZ-T | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12027 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
| ISL12027_10 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
| ISL12027A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
發布緊急采購，3分鐘左右您將得到回復。