- 您現在的位置：買賣IC網 > PDF目錄377579 > IS93C56-3GRI (INTEGRATED SILICON SOLUTION INC) 2,048-BIT SERIAL ELECTRICALLY ERASABLE PROM PDF資料下載
參數資料
| 型號： | IS93C56-3GRI |
| 廠商： | INTEGRATED SILICON SOLUTION INC |
| 元件分類： | DRAM |
| 英文描述： | 2,048-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| 中文描述： | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封裝： | SO-8 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 83K |
| 代理商： | IS93C56-3GRI |
Integrated Silicon Solution, Inc.
—
1-800-379-4774
Rev. G
04/26/01
3
IS93C56-3
ISSI
WRALL instruction is being loaded, the address field
becomes a sequence of
“
Don
’
t Care
”
bits (see Figure 6).
As with the WRITE instruction, if CS is brought HIGH after
a minimum wait of 250 ns (t
CS
), the D
OUT
pin indicates the
READY/
BUSY
status of the chip (see Figure 6).
Write Disable (WDS)
The write disable (WDS) instruction disables all program-
ming capabilities. This protects the entire part against
accidental modification of data until a WEN instruction is
executed. (When Vcc is applied, this part powers up in the
write disabled state.) To protect data, a WDS instruction
should be executed upon completion of each programming
operation. (NOTE: Neither the WEN nor the WDS instruction
has any effect on the READ instruction.) (See Figure 7.)
Erase Register (ERASE)
After the erase instruction is entered, CS must be brought
LOW. The falling edge of CS initiates the self-timed internal
programming cycle. Bringing CS HIGH after a minimum of
t
CS
, will cause D
OUT
to indicate the READ/
BUSY
status of
the chip: a logical
“
0
”
indicates programming is still in
progress; a logical
“
1
”
indicates the erase cycle is complete
and the part is ready for another instruction (see Figure 8).
Erase All (ERAL)
Full chip erase is provided for ease of programming.
Erasing the entire chip involves setting all bits in the entire
memory array to a logical
“
1
”
(see Figure 9).
powers up in the write disabled state. The device then
remains in a write disabled state until a WEN instruction
is executed. Thereafter, the device remains enabled until
a WDS instruction is executed or until Vcc is removed.
(NOTE: Neither the WEN nor the WDS instruction has any
effect on the READ instruction.) (See Figure 4.)
Write (WRITE)
The WRITE instruction includes 16 bits of data to be
written into the specified register. After the last data bit
has been applied to D
IN
, and before the next rising edge of
SK, CS must be brought LOW. The falling edge of CS
initiates the self-timed programming cycle.
After a minimum wait of 250 ns (5V operation) from the
falling edge of CS (t
CS
), if CS is brought HIGH, D
OUT
will
indicate the READY/
BUSY
status of the chip: logical
“
0
”
means programming is still in progress; logical
“
1
”
means
the selected register has been written, and the part is
ready for another instruction (see Figure 5). (NOTE: The
combination of CS HIGH, D
IN
HIGH and the rising edge of
the SK clock, resets the READY/
BUSY
flag. Therefore, it
is important if you want to access the READY/
BUSY
flag
, not to reset it through this combination of control
signals.) Before a WRITE instruction can be executed, the
device must be write enabled (see WEN).
Write All (WRALL)
The write all (WRALL) instruction programs all registers
with the data pattern specified in the instruction. While the
INSTRUCTION SET
Instruction
Start Bit
OP Code
Address
Input Data
READ
1
10
X(A6-A0)
WEN
(Write Enable)
1
00
11XXXXXX
WRITE
1
01
X(A6-A0)
D15-D0
(1)
WRALL
1
00
01XXXXXX
D15-D0
(1)
(Write All Registers)
WDS
(Write Disable)
1
00
00XXXXXX
ERASE
1
11
X(A6-A0)
ERAL
(Erase All Registers)
Note:
1. If input data is not 16 bits exactly, the last 16 bits will be taken as input data (a word).
1
00
10XXXXXX
相關PDF資料 |
PDF描述 |
|---|---|
| IS93C56-3P | 2,048-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56-3PI | 2,048-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56-3 | 2,048-Bit Serial EEPROM(2KB串行EEPROM) |
| IS93C56A | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A-2GRI | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IS93C56-3P | 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:2,048-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56-3PI | 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:2,048-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A | 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A-2GRI | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| IS93C56A-2GRI-TR | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。