- 您現在的位置：買賣IC網 > Datasheet目錄38 > IR1155STRPBF (International Rectifier)IC PFC ONE CYCLE CONTROL 8SOIC Datasheet資料下載
參數資料
| 型號： | IR1155STRPBF |
| 廠商： | International Rectifier |
| 文件頁數： | 13/21頁 |
| 文件大?。?/td> | 388K |
| 描述： | IC PFC ONE CYCLE CONTROL 8SOIC |
| 特色產品： | International Rectifier - uPFC? Power Factor Correction Ics |
| 標準包裝： | 1 |
| 模式： | 連續導電（CCM） |
| 頻率 - 開關： | 可調式 |
| 電流 - 啟動： | 175µA |
| 電源電壓： | 12 V ~ 19 V |
| 工作溫度： | -25°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 標準包裝 |
| 其它名稱： | IR1155STRPBFDKR |
IR1155S
www.irf.com
13
?2011 International Rectifier
IR1155 Pin Description
Pin COM: This is ground potential pin of the IC.
All internal devices are referenced to this point. A
star-connection point, very close to this pin, is
recommended in PCB lay-out in order to
reference the return traces of the various control
loops to the COM potential of the IC.
Pin COMP: External circuitry from this pin to
ground compensates the system voltage loop and
programs the soft start time. The COMP pin is
essentially the output of the voltage error
amplifier. VCOMP is actively discharged using an
internal switch & resistance inside the IC
whenever the IC is pushed into Stand-by mode
(Open Loop Condition) or UVLO/Sleep mode. The
IC is designed not to start-up (from UVLO, Sleep
or Stand-by modes) when there is a pre-bias on
VCOMP pin that is greater than V
COMP,START
. The
VCOMP-COM loop represents a very important
control loop to the IC and hence a dedicated PCB
trace loop is recommended for layout (star-
connection to GND potential) for noise free, stable
operation.
Pin ISNS: ISNS pin is the inverting input to the
current sense amplifier of the IC. The voltage at
this pin is the negative voltage drop sensed
across the system current sense resistor and thus
represents the inductor current sense signal to the
IC for determining gate drive duty cycle. ISNS pin
is also the inverting input to the cycle-by-cycle
peak current limit comparator. Whenever this pin
voltage exceeds V
ISNS(PK)
threshold in magnitude,
the gate drive is instantaneously disabled. Any
external filtering of the ISNS pin must be
performed carefully in order to ensure that the
integrity of the current sense signal is maintained
for cycle-by-cycle protection.
Pin FREQ: This is the user-programmable
frequency pin. The switching frequency is
programmed by inserting a capacitor between
FREQ & COM pins. A pair of current sources
inside the IC source/sink current in/out of the
capacitor alternately thus generating a constant-
slope saw-tooth ramp signal between a pre-
determined peak & valley voltage pair (typically
between 2V to 4V). This saw-tooth signal is the
oscillator signal of the IC. The frequency of
operation of the IC can be programmed anywhere
between 48kHz and 200kHz by suitably sizing the
capacitor.
The FREQ-COM loop represents yet another very
important control loop to the IC and hence a
dedicated PCB trace loop is recommended in lay-
out (star-connection to GND potential) for noise
free, stable operation.
Pin OVP/EN: The OVP/EN pin is connected to the
input of the overvoltage comparator and is used to
detect output overvoltage situations. The output
voltage information is communicated to the OVP pin
using a resistive divider. This pin also serves the
second purpose of an ENABLE pin. The OVP/EN
pin can be used to activate the IC into micropower
sleep mode by pulling the voltage on this pin below
the V
SLEEP
threshold.
Pin VFB: The converter output voltage is sensed
via a resistive divider and fed into this pin. VFB pin
is the inverting input of the output voltage error
amplifier. The non-inverting input of this amplifier is
connected to an internal 5V reference. The
impedance of the divider string must be low enough
that it does not introduce substantial error due to the
input bias currents of the amplifier, yet high enough
to minimize power dissipation. Typical value of
external divider impedance will be 1M&. VFB pin is
also the inverting input to the Open Loop
comparator. The IC is held in Stand-by Mode
whenever VFB pin voltage is below V
OLP
threshold.
Pin VCC: This is the supply voltage pin of the IC
and sense node for the under-voltage lock out
circuit. It is possible to turn off the IC by pulling this
pin below the minimum turn off threshold voltage,
V
CC,UVLO
without damage to the IC. This pin is not
internally clamped.
Pin GATE: This is the gate drive output of the IC.
This drive voltage is internally clamped to 13V(Typ)
and provides a drive current of ?.5A peak with
matched rise and fall times.
相關PDF資料 |
PDF描述 |
|---|---|
| IRS2500SPBF | IC PFC |
| IRS2548DSPBF | IC PFC |
| IRS2580DSPBF | IC PFC |
| ISL6111CR-T | IC CTRLR HOT PLUG SWITCH 20-QFN |
| ISL6112INZA-T | IC PWR CNTRLR DUAL SLT 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IR11662S | 制造商:IRF 制造商全稱:International Rectifier 功能描述:ADVANCED SMART RECTIFIER TM CONTROL IC |
| IR11662SPBF | 功能描述:開關變換器、穩壓器與控制器 200V SECONDARY SIDE HI SPEED SR CTRLLER RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| IR11662STRPBF | 功能描述:開關變換器、穩壓器與控制器 FLYBACK SYNCH REC IC +1,-3.5A RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| IR1166SPBF | 功能描述:IC REG CTLR SW 200V 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:SmartRectifier™ 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
| IR1166SPBF_09 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:SmartRectifier CONTROL IC Secondary side high speed SR controller |
發布緊急采購，3分鐘左右您將得到回復。