參數資料
型號： INA-32063-BLK
英文描述： IC-WIDEBAND RF AMPLIFIER
中文描述： 集成電路寬帶射頻放大器
文件頁數： 7/11頁
文件大?。?/td> 89K
代理商： INA-32063-BLK
7
PCB Materials
Typical choices for PCB material
for low cost wireless applications
are FR-4 or G-10 with a thickness
of 0.025 (0.636 mm) or 0.031 inches
(0.787 mm). A thickness of 0.062
inches (1.574 mm) is the maximum
that is recommended for use with
this particular device. The use of a
thicker board material increases
the inductance of the plated
through vias used for RF grounding
and may deteriorate circuit
performance. Adequate grounding
is needed not only to obtain
maximum amplifier performance
but also to reduce any possibility
of instability.
Phase Reference Planes
The positions of the reference
planes used to measure
S-Parameters for this device are
shown in Figure 19. As seen in the
illustration, the reference planes
are located at the point where the
package leads contact the test
circuit.
REFERENCE
PLANES
TEST CIRCUIT
Figure 19. Phase Reference Planes.
SOT-363 PCB Layout
The INA-31063 is packaged in the
miniature SOT-363 (SC-70)
surface mount package. A PCB
pad layout for the SOT-363
package is shown in Figure 20
(dimensions are in inches). This
layout provides ample allowance
for package placement by auto-
mated assembly equipment
without adding pad parasitics that
could impair the high frequency
performance of the INA-31063
The layout that is shown with a
nominal SOT-363 package foot-
print superimposed on the PCB
pads for reference.
0.026
0.075
0.016
0.035
Figure 20. PCB Pad Layout for
INA-31063 ( dimensions in inches) .
Statistical Parameters
Several categories of parameters
appear within this data sheet.
Parameters may be described
with values that are either
“minimum or maximum,” “typi-
cal,” or “standard deviations.” The
values for parameters are based
on comprehensive product
characterization data, in which
automated measurements are
made on a large number of parts
taken from 3 non-consecutive
process lots of semiconductor
wafers. The data derived from
product characterization tends to
be normally distributed, e.g., fits
the standard “bell curve.” Param-
eters considered to be the most
important to system performance
are bounded by minimum or
maximum values. For the
INA-31063, these parameters are:
Power Gain ( |S21|
2
), and the
Device Current (I
d
). Each of these
guaranteed parameters is 100%
tested. Values for most of the
parameters in the table of Electri-
cal Specifications that are de-
scribed by typical data are the
mathematical mean (
μ
), of the
normal distribution taken from
the characterization data. For
parameters where measurements
or mathematical averaging may
not be practical, such as
S-parameters or Noise Param-
eters and the performance
curves, the data represents a
nominal part taken from the
“center” of the characterization
distribution. Typical values are
intended to be used as a basis for
electrical design.
To assist designers in optimizing
not only the immediate circuit
using the INA-31063, but to also
optimize and evaluate trade-offs
that affect a complete wireless
system, the standard deviation
(
σ
) is provided for three of the
Electrical Specifications param-
eters (at 25
°
C) in addition to the
mean. The standard deviation is a
measure of the variability about
the mean. It will be recalled that a
normal distribution is completely
described by the mean and
standard deviation. Standard
statistics tables or calculations
provide the probability of a
parameter falling between any
two values, usually symmetrically
located about the mean. Referring
to Figure 21 for example, the
probability of a parameter being
between
±
1
σ
is 68.3%; between
±
2
σ
is 95.4%; and between
±
3
σ
is
99.7%.
68%
95%
99%
Parameter Value
Mean
(
μ
), typ
-3
σ
-2
σ
-1
σ
+1
σ
+2
σ
+3
σ
Figure 21. Normal Distribution.
相關PDF資料
PDF描述
INA-34063 3V Fixed Gain. Medium Power Amplifier
INA-34063-BLK IC-RF AMPLIFIER MED. PWR.
INA-32063 3.0 GHz Wideband Silicon RFIC Amplifier(3.0 GHz 寬頻帶硅射頻集成電路放大器)
INA-34063 3.0 GHz Medium Power Silicon RFIC Amplifier(3.0 GHz中等功率硅射頻集成電路放大器)
INA-50311 1 GHz Low Noise Silicon MMIC Amplifier
相關代理商/技術參數
參數描述
INA-32063-TR1 制造商:AGILENT 制造商全稱:AGILENT 功能描述:3.0 GHz Wideband Silicon RFIC Amplifier
INA-32063-TR2 制造商:AGILENT 制造商全稱:AGILENT 功能描述:3.0 GHz Wideband Silicon RFIC Amplifier
INA321 制造商:TI 制造商全稱:Texas Instruments 功能描述:microPower, Single-Supply, CMOS Instrumentation Amplifier
INA321E 制造商:Texas Instruments 功能描述:AMP INSTRUMENTATION VSSOP8 321
INA321E/250 功能描述:儀表放大器 Micropwr Single-sply CMOS RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*