- 您現在的位置：買賣IC網 > PDF目錄360860 > INA-12063 1.5 GHz Low Noise Self-Biased Transistor Amplifier PDF資料下載
參數資料
| 型號： | INA-12063 |
| 英文描述： | 1.5 GHz Low Noise Self-Biased Transistor Amplifier |
| 中文描述： | 1.5 GHz的低噪聲自偏置晶體管放大器 |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 351K |
| 代理商： | INA-12063 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁
6-134
A Note on Supply Line
Bypassing
When multiple bypass capacitors
are used throughout the power
supply lines in a wireless system,
consideration should be given to
potential resonances. It is impor-
tant to ensure that the capacitors,
when combined with additional
parasitic L’s and C’s on the circuit
board, do not form resonant
circuits. The addition of a small
value resistor in the bias supply
line between bypass capacitors
will often “de-Q” the bias circuit
and eliminate resonance effects.
SMT Assembly
Reliable assembly of surface
mount components is a complex
process that involves many
material, process, and equipment
factors, including: method of
heating (e.g., IR or vapor phase
reflow, wave soldering, etc.)
circuit board material, conductor
thickness and pattern, type of
solder alloy, and the thermal
conductivity and thermal mass of
components. Components with a
low mass, such as the SOT-363
package, will reach solder reflow
temperatures faster than those
with a greater mass.
The INA-12063 is has been
qualified to the time-temperature
profile shown in Figure 29. This
profile is representative of an IR
reflow type of surface mount
assembly process.
After ramping up from room
temperature, the circuit board
with components attached to it
(held in place with solder paste)
passes through one or more
preheat zones. The preheat zones
increase the temperature of the
board and components to prevent
thermal shock and begin evapo-
rating solvents from the solder
paste. The reflow zone briefly
elevates the temperature suffi-
ciently to produce a reflow of the
solder.
The rates of change of tempera-
ture for the ramp-up and cool-
down zones are chosen to be low
enough to not cause deformation
of the board or damage to compo-
nents due to thermal shock. The
maximum temperature in the
reflow zone (T
MAX
) should not
exceed 235
°
C.
These parameters are typical for
a surface mount assembly
process for the INA-12063. As a
general guideline, the circuit
board and components should be
exposed only to the minimum
temperatures and times neces-
sary to achieve a uniform reflow
of solder.
Statistical Parameters
Several categories of parameters
appear within this data sheet.
Parameters may be described
with values that are either
minimum or maximum, “typical,”
or standard deviations.
The values for parameters are
based on comprehensive product
characterization data, in which
automated measurements are
made on of a minimum of 500
parts taken from 3 non-consecu-
tive process lots of semiconduc-
tor wafers. The data derived from
product characterization tends to
be normally distributed, e.g., fits
the standard bell curve.
Parameters considered to be the
most important to system perfor-
mance are bounded by
minimum
or
maximum
values. For the
INA-12063, these parameters are:
Power Gain (|S
21
|
2
), Noise Figure
(NF), and Device Current. Each
of these guaranteed parameters is
100% tested.
Values for most of the parameters
in the table of Electrical Specifi-
cations that are described by
typical
data are the mathematical
mean (
μ
), of the normal distribu-
tion taken from the characteriza-
tion data. For parameters where
measurements or mathematical
averaging may not be practical,
such as S-parameters or Noise
Parameters and the performance
curves, the data represents a
nominal part taken from the
center of the characterization
distribution. Typical values are
intended to be used as a basis for
electrical design.
TIME (seconds)
T
MAX
T
°
C
0
0
50
100
150
200
250
60
Preheat
Zone
Cool Down
Zone
Reflow
Zone
120
180
240
300
Figure 29. Surface Mount Assembly Profile.
相關PDF資料 |
PDF描述 |
|---|---|
| INA-12063-BLK | 1.5 GHz Low Noise Self-Biased Transistor Amplifier |
| INA-12063-TR1 | 1.5 GHz Low Noise Self-Biased Transistor Amplifier |
| INA-30311 | GT 14C 14#16 SKT PLUG |
| INA-30311-BLK | 1 GHz Low Noise Silicon MMIC Amplifier |
| INA-30311-TR1 | 1 GHz Low Noise Silicon MMIC Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA-12063-BLK | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:1.5 GHz Low Noise Self-Biased Transistor Amplifier |
| INA-12063-TR1 | 制造商:Agilent Technologies 功能描述: |
| INA120AP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:INSTRUMENTATION AMPLIFIER |
| INA120BG | 制造商:TI 制造商全稱:Texas Instruments 功能描述:INSTRUMENTATION AMPLIFIER |
| INA120BP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:INSTRUMENTATION AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。