![](http://datasheet.mmic.net.cn/100000/IMIC9806IAT_datasheet_3494099/IMIC9806IAT_2.png)
C9806I
I
2C Frequency Clock Generator for Mobile Pentium II Applications.
Preliminary
INTERNATIONAL MICROCIRCUITS, INC. 525 LOS COCHES ST.
Rev.1.0
4/25/2000
MILPITAS, CA 95035. TEL: 408-263-6300. FAX 408-263-6571
Page 2 of 14
http://www.imicorp.com
Pin Description
Pin No.
Pin Name
PWR
I/O
TYPE
Description
1,2,45, 47
REF(0:3)
VDD
O
Buffer output clocks of the reference signal at Xin.
4
Xin
VDD
I
OSC
On-chip reference oscillator input pin. Requires either an
external parallel resonant crystal (nominally 14.318 MHz) or
externally generated reference signal
5
Xout
VDD
O
OSC
On-chip reference oscillator output pin. Drives an external
parallel resonant crystal. When an externally generated
reference signal is used at Xin, this pin remains unconnected.
6
S1
I
PD
Input for selecting CPU//PCI frequencies (see table 1,p.1).
18
S0
I
PU
Input for selecting CPU//PCI frequencies (see table 1,p.1).
8,9,11,12,
13,14,16
PCI_F,
PCI(0:5)
VDD
O
PCI clock outputs, synchronous to the CPU clocks. If PCI_STP#
is asserted low, PCI (0:5) stop in a low state, PCI_F does NOT.
19
SDATA
VDD
I/O
PU
Serial data input pin. Conforms to the Philips I2C specification of
a Slave Receiver device. This pin is an input when receiving
data. It is an open drain output when acknowledging. See I2C
function description, p.5.
20
SCLK
VDD
I
PU
Serial clock input pin. Conforms to the Philips I2C 100KHz
Specification.
22,23
24/48M
VDD
O
Programmable Peripheral clock outputs. Default to 48mhz for
USB, but can be programmed to 24MHz through I2C bus.
26
PCI_STP#
VDD
I
PU
Input pin for stopping PCI (0:5) when active low. Default high.
(see power management description p.3 )
27
CPU_STP#
VDD
I
PU
Input pin for stopping CPU (0:1) when active low. Default high.
(see power management description p.3 ). If Byte1, Bit2 and I
2C
is low (0), then CPU0 DOES NOT STOP.
29,30,32,
33, 35, 36,
38
SDRAM
(FB,0:5)
VDDS
O
SDRAM clock outputs. They are buffered outputs of the signal
applied at SDRAM_IN, pin39.
41,42
CPU(0:1)
VDDC
O
Host (CPU) Clock outputs. See Table 1,p.1 for frequency
selection.
44
PWR_DWN#
VDD
I
PU
Input pin for shutting down the device when asserted low. All
outputs with the exception of SDRAM (FB,0:5), PLL’s and crystal
are stopped for minimum power consumption.
7,15,21,25
46, 48
VDD
-
P
-
3.3 Volt common power supply pins.
28,34
VDDS
-
P
-
3.3 Volt power supply pins for SDRAM_IN, SDRAM (FB, 0:5)
outputs.
40
VDDC
-
P
-
3.3 or 2.5 Volt power supply pins for the CPU (0:1), outputs.
3,10,17,
24, 31, 37,
43
VSS
-
P
-
Common Ground pins.
39
SDRAM_IN
VDD
I
-
Input to SDRAM buffers.
Table 2
A bypass capacitor (0.1 uF) should be placed as close as possible to each Vdd, Vddc, and Vdds pins. If these
bypass capacitors are not close to the pins, their high frequency filtering characteristic will be canceled by the
lead inductance of the traces.