- 您現在的位置：買賣IC網 > PDF目錄67708 > ICS952621YFLF-T (INTEGRATED DEVICE TECHNOLOGY INC) 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF資料下載
參數資料
| 型號： | ICS952621YFLF-T |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封裝： | LEAD FREE, MO-118, SSOP-48 |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 155K |
| 代理商： | ICS952621YFLF-T |
14
Integrated
Circuit
Systems, Inc.
ICS952621
0756C—04/19/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm (10K)
resistor is used to provide both the solid CMOS programming
voltage needed during the power-up programming period and to
provide an insignificant load on the output clock during the
subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS952621YGLF-T | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952623YGLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS952624YFLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952702YFLFT | 222 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952702YFT | 222 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS952623 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for Next Gen P4 processor |
| ICS952623YFT | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for Next Gen P4 processor |
| ICS952623YGT | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for Next Gen P4 processor |
| ICS952702 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for K7 System |
| ICS952702YFLF-T | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for K7 System |
發布緊急采購，3分鐘左右您將得到回復。