- 您現在的位置：買賣IC網 > PDF目錄360786 > ICS952607YFLF-T Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:TV01; Number of Contacts:6; Connector Shell Size:9; Connecting Termination:Crimp; Circular Shell Style:Straight Receptacle; Body Style:Straight PDF資料下載
參數資料
| 型號： | ICS952607YFLF-T |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:TV01; Number of Contacts:6; Connector Shell Size:9; Connecting Termination:Crimp; Circular Shell Style:Straight Receptacle; Body Style:Straight |
| 中文描述： | 可編程定時控制中心，為下一代P4處理器 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 214K |
| 代理商： | ICS952607YFLF-T |
16
Integrated
Circuit
Systems, Inc.
ICS952607
Advance Information
0734—07/16/04
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm (10K)
resistor is used to provide both the solid CMOS programming
voltage needed during the power-up programming period and to
provide an insignificant load on the output clock during the
subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
8.2K
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS952607 | 16-Bit Buffers/Drivers With 3-State Outputs 48-SSOP -40 to 85 |
| ICS952621 | Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
| ICS952702 | Programmable Timing Control Hub for K7 System |
| ICS952703 | Programmable Timing Control Hub for K7 System |
| ICS952801 | Programmable Timing Control HubTM for K8TM processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS952620CFLF | 功能描述:IC TIMING CTRL HUB P4 48-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS952620CFLFT | 功能描述:IC TIMING CTRL HUB P4 48-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS952621 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
| ICS952623 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for Next Gen P4 processor |
| ICS952623YFT | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for Next Gen P4 processor |
發布緊急采購，3分鐘左右您將得到回復。