- 您現在的位置：買賣IC網 > PDF目錄383077 > ICE1PCS02G (INFINEON TECHNOLOGIES AG) Standalone Power Factor Correction (PFC) Controller in Continuous Conduction Mode (CCM) with Input Brown-Out Protection PDF資料下載
參數資料
| 型號： | ICE1PCS02G |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Standalone Power Factor Correction (PFC) Controller in Continuous Conduction Mode (CCM) with Input Brown-Out Protection |
| 中文描述： | 單機功率因數校正在連續導通模式（CCM）（PFC）控制器具有輸入欠壓保護 |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 404K |
| 代理商： | ICE1PCS02G |
CCM-PFC
ICE1PCS02/G
Functional Description
3
Version 1.1
7
28 Dec 2004
3.1
General
The ICE1PCS02/G is a 8 pin control IC for power factor
correction converters. It comes in both DIP and DSO
packages and is suitable for wide range line input
applications from 85 to 265 VAC. The IC supports
converters in boost topology and it operates in
continuous conduction mode (CCM) with average
current control.
It is a design derivative from the ICE1PCS01/G with the
differences in the supporting functions, namely the
input brown-out detection, internal fixed switching
frequency 65kHz and shortened startup time.
The IC operates with a cascaded control; the inner
current loop and the outer voltage loop. The inner
current loop of the IC controls the sinusoidal profile for
the average input current. It uses the dependency of
the PWM duty cycle on the line input voltage to
determine the corresponding input current. This means
the average input current follows the input voltage as
long as the device operates in CCM. Under light load
condition, depending on the choke inductance, the
system may enter into discontinuous conduction mode
(DCM) resulting in a higher harmonics but still meeting
the Class D requirement of IEC 1000-3-2.
The outer voltage loop controls the output bus voltage.
Depending on the load condition, OTA1 establishes an
appropriate voltage at VCOMP pin which controls the
amplitude of the average input current.
The IC is equipped with various protection features to
ensure safe operating condition for both the system
and device.
3.2
Power Supply
An internal under voltage lockout (UVLO) block
monitors the VCC power supply. As soon as it exceeds
11.2V and both voltages at pin 6 (VSENSE) >0.8V and
pin 4 (VINS) >1.5V, the IC begins operating its gate
drive and performs its Startup as shown in Figure 3.
.
Figure3
State of Operation respect to VCC
If VCC drops below 10.2V, the IC is off. The IC will then
be consuming typically 200
μ
A, whereas consuming
18mA during normal operation.
The IC can be turned off and forced into standby mode
by pulling down the voltage at pin 6 (VSENSE) to lower
than 0.8V. In this standby mode, the current
consumption is reduced to 3mA. Other condition that
can result in the standby mode is when a Brown-out
condition occurs, ie pin 4 (VINS) <0.8V.
3.3
Start-up
Figure 4 shows the operation of voltage loop’s OTA1
during startup. The VCOMP pin is pull internally to
ground via switch S1 during UVLO and other fault
conditions (see later section on “System Protection”).
During power up when V
is less than 85% of the
rated level, it sources a constant 30
μ
A into the
compensation network at pin 5 (VCOMP) causing the
voltage at this pin to rise linearly. This results in a
controlled linear increase of the input current from 0A
thus reducing the stress on the external component.
Figure4
Startup Circuit
As V
has not reached within 5% from the rated
value, VCOMP voltage is level-shifted by the window
detect block as shown in Figure 5, to ensure there is no
long period of low or no current.
When V
approaches its rated value, OTA1’s
sourcing current drops and so does the level shift of the
window detect block. The normal voltage loop then
takes control.
V
CC
(
V
VSENSE
> 0.8 V)
AND (
V
VINS
> 1.5 V)
11.2 V
10.5 V
t
OFF
Start
Up
Open loop/
Standby
Normal
Operation
IC's
State
OFF
Normal
Operation
(
V
VSENSE
< 0.8 V)
OR (
V
VINS
< 0.8 V)
(
V
VSENSE
> 0.8 V)
AND (
V
VINS
> 1.5 V)
VCOMP
C5
C4
VSENSE
OTA1
5V
ICE1PCS02/G
fault
R3 + R4
R4
x V
OUT
)
(
R6
S1
+/-30uA, 42uS
Functional Description
相關PDF資料 |
PDF描述 |
|---|---|
| ICE2A165 | Off-Line SMPS Current Mode Controller with integrated 650V/800V CoolMOS⑩ |
| ICE2A180 | Off-Line SMPS Current Mode Controller with integrated 650V/800V CoolMOS⑩ |
| ICE2A265 | Off-Line SMPS Current Mode Controller with integrated 650V/800V CoolMOS⑩ |
| ICE2A280 | Off-Line SMPS Current Mode Controller with integrated 650V/800V CoolMOS⑩ |
| ICE2A365 | Off-Line SMPS Current Mode Controller with integrated 650V/800V CoolMOS⑩ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICE1PCS02GFUMA1 | 制造商:Infineon Technologies AG 功能描述:Power Factor Correction CONTRLR 0.1mA 70KHz 8-Pin DSO 制造商:Infineon Technologies AG 功能描述:AC/DC STANDALONE - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC PFC CONTROLLER CCM DSO8 |
| ICE1PCS02GZT | 制造商:Infineon Technologies AG 功能描述:Power Factor Correction CONTRLR 0.1mA 70KHz 8-Pin DSO T/R |
| ICE1PD265G | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Power Factor Controller + Cool- MOS: BoostSET IC for High Power Factor and low THD |
| ICE1QS01 | 功能描述:軟開關 PWM 控制器 QUASI-REISTANT PWM CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ICE1QS01G | 功能描述:軟開關 PWM 控制器 PWM-QR CONTROL IC FOR SMPS RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。