- 您現在的位置：買賣IC網 > PDF目錄299188 > HY29F002BC-45I (HYNIX SEMICONDUCTOR INC) 256K X 16 FLASH 5V PROM, 45 ns, PQCC32 PDF資料下載
參數資料
| 型號： | HY29F002BC-45I |
| 廠商： | HYNIX SEMICONDUCTOR INC |
| 元件分類： | PROM |
| 英文描述： | 256K X 16 FLASH 5V PROM, 45 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 5/40頁 |
| 文件大?。?/td> | 457K |
| 代理商： | HY29F002BC-45I |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
13
HY29F002
Rev. 4.0/Jan. 00
may be loaded in any sequence, and the number
of sectors specified may be from one sector to all
sectors. The only restriction is that the time be-
tween these additional data cycles must be less
than 50 s, otherwise erasure may begin before
the last data cycle is accepted. To ensure that all
data cycles are accepted, it is recommended that
host processor interrupts be disabled during the
time that the additional cycles are being issued
and then be re-enabled afterwards.
Note: The device is capable of accepting three ways
of invoking Erase Commands for additional sectors
during the time-out window. The preferred method,
described above, is the sector erase data cycle after
the initial six bus cycle command sequence. However,
the device also accepts the following methods of
specifying additional sectors during the sector erase
time-out:
Repeat the entire six-cycle command sequence, speci-
fying the additional sector in the sixth cycle.
Repeat the last three cycles of the six-cycle command
sequence, specifying the additional sector in the third
cycle.
If all sectors scheduled for erasing are within pro-
tected sectors, the device returns to reading ar-
ray data after approximately 100 s. If at least
one selected sector is not protected, the erase
operation erases the unprotected sectors, and ig-
START
YES
Erase An
Additional Sector?
Check Erase Status
(See Write Operation Status
Section)
Setup First (or Next) Sector
Address for Erase Operation
ERASE COMPLETE
Write First Five Cycles of
SECTOR ERASE
Command Sequence
Write Last Cycle (SA/0x30)
of SECTOR ERASE
Command Sequence
Sector Erase
Time-out (DQ[3])
Expired?
NO
YES
NO
GO TO
ERROR RECOVERY
DQ[5] Error Exit
Normal Exit
Sectors which require erasure
but which were not specified in
this erase cycle must be erased
later using a new command
sequence
Figure 6. Sector Erase Procedure
nores the command for the selected sectors that
are protected.
The system can monitor DQ[3] to determine if the
50 s sector erase time-out has expired, as de-
scribed in the Write Operation Status section. If
the time between additional sector erase data
cycles can be insured to be less than the time-
out, the system need not monitor DQ[3].
Any command other than Sector Erase or Erase
Suspend during the time-out period resets the
device to reading array data. The system must
then rewrite the command sequence, including any
additional sector erase data cycles. Once the
sector erase operation itself has begun, only the
Erase Suspend command is valid. All other com-
mands are ignored.
As for the Chip Erase command, note that a hard-
ware reset immediately terminates the erase op-
eration. To ensure data integrity, the aborted Sec-
tor Erase command sequence should be reissued
once the reset operation is complete.
When the Automatic Erase algorithm terminates,
the device returns to the Read mode. Several
methods are provided to allow the host to deter-
mine the status of the erase operation, as de-
scribed in the Write Operation Status section.
相關PDF資料 |
PDF描述 |
|---|---|
| HY29F400TR-12 | 512K X 8 FLASH 5V PROM, 120 ns, PDSO48 |
| HY5117800CT-60 | 2M X 8 FAST PAGE DRAM, 60 ns, PDSO28 |
| HY51V64804LTC-50 | 8M X 8 EDO DRAM, 50 ns, PDSO32 |
| HY628100ALLP-70I | 128K X 8 STANDARD SRAM, 70 ns, PDIP32 |
| HY628100ALLG-85I | 128K X 8 STANDARD SRAM, 85 ns, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY29F002BC-55 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002BC-55E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002BC-55I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002BC-70 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002BC-70E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。