參數資料
型號： HT48CA3
廠商： Holtek Semiconductor Inc.
英文描述： 8-Bit Remote Type MCU
中文描述： 8位遙控型單片機
文件頁數： 9/36頁
文件大小： 271K
代理商： HT48CA3
HT48CA3
Rev. 1.40
9
July 16, 2003
period of approximately 90 s. The WDT oscillator can
be disabled by ROM code option to conserve power.
Watchdog Timer
WDT
The WDT clock source is implemented by a dedicated
RC oscillator (WDT oscillator), instruction clock (system
clock divided by 4), determines the ROM code option.
This timer is designed to prevent a software malfunction
or sequence from jumping to an unknown location with
unpredictable results. The Watchdog Timer can be dis-
abled by ROM code option. If the Watchdog Timer is dis-
abled, all the executions related to the WDT result in no
operation.
Once the internal WDT oscillator (RC oscillator with a
period of 90 s@3V normally) is selected, it is first di-
vided by 256 (8-stage) to get the nominal time-out pe-
riod of 23ms@3V. This time-out period may vary with
temperatures, VDD and process variations. By invoking
the WDT prescaler, longer time-out periods can be real-
ized. Writing data to WS2, WS1, WS0 (bit 2,1,0 of the
WDTS) can give different time-out periods. If WS2,
WS1, and WS0 are all equal to 1, the division ratio is up
to 1:128, and the maximum time-out period is 2.9s/3V
seconds. If the WDT oscillator is disabled, the WDT
clock may still come from the instruction clock and oper-
ates in the same manner except that in the HALT state
the WDT may stop counting and lose its protecting pur-
pose. In this situation the logic can only be restarted by
external logic. The high nibble and bit 3 of the WDTS are
reserved for user s defined flags, which can be used to
indicate some specified status.
If the device operates in a noisy environment, using the
on-chip RC oscillator (WDT OSC) is strongly recom-
mended, since the HALT will stop the system clock.
WS2
WS1
WS0
Division Ratio
0
0
0
1:1
0
0
1
1:2
0
1
0
1:4
0
1
1
1:8
1
0
0
1:16
1
0
1
1:32
1
1
0
1:64
1
1
1
1:128
WDTS register
The WDT overflow under normal operation will initialize
chip reset and set the status bit TO . But in the HALT
mode, the overflow will initialize a warm reset and only
the PC and SP are reset to zero. To clear the contents of
WDT (including the WDT prescaler), three methods are
adopted;externalreset(alowleveltoRES),softwarein-
structionanda HALT instruction.Thesoftwareinstruc-
tion include
CLR WDT
and the other set
CLR
WDT1 and CLR WDT2 . Of these two types of instruc-
tion, only one can be active depending on the ROM
code option
CLR WDT times selection option . If the
CLR WDT
is selected (i.e. CLR WDT times equal
one), any execution of the CLR WDT instruction will
clear the WDT. In the case that CLR WDT1 and CLR
WDT2 are chosen (i.e. CLR WDT times equal two),
these two instructions must be executed to clear the
WDT; otherwise, the WDTmay reset the chip as a result
of time-out.
Power Down Operation
HALT
The HALT mode is initialized by the HALT instruction
and results in the following...
The system oscillator will be turned off but the WDT
oscillator remains running (if the WDT oscillator is se-
lected).
The contents of the on chip RAM and registers remain
unchanged.
WDT and WDT prescaler will be cleared and re-
counted again (if the WDT clock is from the WDT os-
cillator).
All of the I/O ports maintain their original status.
The PD flag is set and the TO flag is cleared.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge sig-
nal on port A or a WDT overflow. An external reset
causes a device initialization and the WDToverflow per-
forms a warm reset . After the TO and PD flags are ex-
amined, the reason for chip reset can be determined.
The PD flag is cleared by system power-up or executing
the CLR WDT instruction and is set when executing
the HALT instruction. The TO flag is set if the WDT
time-out occurs, and causes a wake-up that only resets
thePCandSP;theothersremainintheiroriginalstatus.
The port A wake-up and interrupt methods can be con-
sidered as a continuation of normal execution. Each bit
&
!
,
; 1
2 9 < # ! ,
!
+
,
/ 9 < # ! ,
!
2 9 ! 9 ,
+
, #
9
!
+
. +
'
" ! #
!
+
Watchdog Timer
相關PDF資料
PDF描述
HT48E06 8-Bit I/O Type MCU (With EEPROM)
HT48E50 I/O Type 8-Bit MTP MCU With EEPROM
HT48R05A-1 8-Bit High Performance RISC-like OTP Microcontroller(8位、高性能、類似RISC、一次可編程微控制器，用于多I/O接口設備)
HT48R05A 8-Bit OTP Microcontroller
HT48R06A-1 8-Bit High Performance RISC-like OTP Microcontroller(8位、高性能、類似RISC、一次可編程微控制器，用于多I/O接口設備)
相關代理商/技術參數
參數描述
HT48CA5 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU
HT48CA6 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Remote Type Low Voltage Mask MCU
HT48CU80 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type 8-Bit MCU
HT48CXX 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Microcontroller Series
HT48E06 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit I/O Type MCU (With EEPROM)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*