- 您現在的位置：買賣IC網 > PDF目錄370661 > HPC3130APBM (Texas Instruments, Inc.) PCI Bus Interface/Controller PDF資料下載
參數資料
| 型號： | HPC3130APBM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | PCI Bus Interface/Controller |
| 中文描述： | PCI總線接口/控制器 |
| 文件頁數： | 13/41頁 |
| 文件大?。?/td> | 537K |
| 代理商： | HPC3130APBM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
HPC3130A
PCI HOT PLUG CONTROLLER
SCPS055 – NOVEMBER 1999
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions (Continued)
system interface
TERMINAL
NO.
120
NAME
NO.
128
NO.
144
I/O
FUNCTION
FRAME
20
21
23
I
Frame. This input and the IRDY input indicate that the PCI bus is idle. When the HPC3130A
senses the PCI bus is idle after IDLEGNT is low, a hot-plug slot can be connected to the PCI
bus. This input must be wired to a valid logic level if the bus idling procedure is not implemented.
IDLEGNT
19
20
22
I
Idle grant. This input indicates when the PCI bus is idled by the HOST-PCI bridge after a
request is made by IDLEREQ. The protocol is identical to PCI request/grant. This input must be
wired to a valid logic level if the bus idling procedure is not implemented.
IDLEREQ
18
19
21
O
Idle request. This output is driven to request the HOST-PCI bridge to idle the PCI bus before
connecting a hot-plug slot. The protocol is identical to PCI request/grant. A pullup resistor must
be implemented on this terminal if the bus idling procedure is not implemented.
INTR
24
25
27
O
System interrupt. This output provides a system interrupt. The HPC3130A can be programmed
to assert this interrupt under various conditions, which may be serviced by the hot-plug service.
Furthermore, the event status/enable state is compliant with the ACPI Specificationand, as a
result, supports ACPI control methods for switching the HPC3130A.
INTR
23
24
26
O
System interrupt. This open drain output provides a system interrupt. The HPC3130A can be
programmed to assert this interrupt under various conditions, which may be serviced by the
hot-plug. Furthermore, the event status/enable state is compliant with the ACPI Specification
and, as a result, supports ACPI control methods for switching the HPC3130A.
IRDY
21
22
24
I
Initiator ready. This and the FRAME input indicate that the PCI bus is idle. When the HPC3130A
senses the PCI bus is idle after IDLEGNT is low, a hot-plug slot may be connected to the PCI
bus. This input must be wired to a valid logic level if the bus idling procedure is not implemented.
PCLK
16
17
19
I
PCI clock input. These terminals provide the PCI clock to the HPC3130A, which uses it only for
activity indicator timing, IDLEREQ/IDLEGNT protocol, and connection sequencing.
PRST
14
15
17
I
PCI reset. This signal provides the PCI reset to the HPC3130A. After a PCI reset, the
HPC3130A resides in a state where all slots are enabled, as in a non-hot-plug system. The
HPC3130A passes PCI resets from the host to all hot-plug slots.
SGNT
13
14
16
O
Secondary grant. This output provides a scheme to cascade a secondary HPC3130A device in
order to provide more than four slots. The SGNT output from the primary HPC3130A is input to
the IDLEGNT terminal for the secondary HPC3130A. After the secondary HPC3130A requests
the primary HPC3130A to idle the bus, the primary HPC3130A arbitrates for the bus using
IDLEREQ. Once IDLEGNT is asserted, the primary HPC3130A asserts its SGNT output. This
indicates to the secondary HPC3130A device that it can connect to the bus.
SMODE
27
28
30
I
Serial bus mode. When this input is asserted high, the internal HPC3130A registers are
accessible through the serial bus interface; otherwise, they are accessed through the generic
parallel bus interface. This input selects the control bus interface.
SREQ
12
13
15
I
Secondary request. This input provides a scheme to cascade a second HPC3130A device in
order to provide more than four slots. The IDLEREQ from the second HPC3130A device is
input to the SREQ terminal of the primary HPC3130A. If the second HPC3130A device
arbitrates for the bus by asserting its IDLEREQ output, this scheme causes the primary
HPC3130A to assert its IDLEREQ. If cascading is not used, this input is pulled high.
SYSM66EN
25
26
28
I/O
PCI bus frequency indicator. This signal indicates the PCI clock frequency requirements of the
hot-plug slots, and must be tied to the system PCI bus M66EN signal. The output from this
terminal only changes state after a PCI reset and is only required in a 66-MHz system.
相關PDF資料 |
PDF描述 |
|---|---|
| HPC3130APBKLOW-PROFILEQUA | DIODE ZENER DUAL COMMON-CATHODE 300mW 33Vz 5mA-Izt 0.0606 0.1uA-Ir 25 SOT-23 3K/REEL |
| HPC3130PGELOW-PROFILEQUAD | PCI HOT PLUG CONTROLLER |
| HPC3130PBMQUADFLAT | PCI HOT PLUG CONTROLLER |
| HPC3130PBKLOW-PROFILEQUAD | PCI HOT PLUG CONTROLLER |
| HPC43100VHG30 | 16-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPC3130APBMQUADFLAT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCI HOT PLUG CONTROLLER |
| HPC3130APGE | 功能描述:外圍驅動器與原件 - PCI HOT PLUG CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| HPC3130APGEG4 | 功能描述:外圍驅動器與原件 - PCI HOT PLUG CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| HPC3130APGELOW-PROFILEQUA | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCI HOT PLUG CONTROLLER |
| HPC3130PBK | 功能描述:外圍驅動器與原件 - PCI HOT PLUG CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。