參數資料
型號： HPC-DEV-WDBC
廠商： National Semiconductor Corporation
英文描述： High-Performance microController with A/D
中文描述： 高性能微控制器/數
文件頁數： 25/39頁
文件大?。?/td> 430K
代理商： HPC-DEV-WDBC
HPC46164 UART
The HPC46164 contains a software programmable UART.
The UART (seeFigure 26 ) consists of a transmit shift regis-
ter, a receiver shift register and five addressable registers,
as follows: a transmit buffer register (TBUF), a receiver buff-
er register (RBUF), a UART control and status register
(ENU), a UART receive control and status register (ENUR)
and a UART interrupt and clock source register (ENUI). The
ENU register contains flags for transmit and receive func-
tions; this register also determines the length of the data
frame (8 or 9 bits) and the value of the ninth bit in transmis-
sion. The ENUR register flags framing and data overrun er-
rors while the UART is receiving. Other functions of the
ENUR register include saving the ninth bit received in the
data frame and enabling or disabling the UART’s Wake-up
Mode of operation. The determination of an internal or ex-
ternal clock source is done by the ENUI register, as well as
selecting the number of stop bits and enabling or disabling
transmit and receive interrupts.
The baud rate clock for the Receiver and Transmitter can
be selected for either an internal or external source using
two bits in the ENUI register. The internal baud rate is pro-
grammed by the DIVBY register. The baud rate may be se-
lected from a range of 8 Hz to 128 kHz in binary steps or T3
underflow. By selecting a 9.83 MHz crystal, all standard
baud rates from 75 baud to 38.4 kBaud can be generated.
The external baud clock source comes from the CKX pin.
The Transmitter and Receiver can be run at different rates
by selecting one to operate from the internal clock and the
other from an external source.
The HPC46164 UART supports two data formats. The first
format for data transmission consists of one start bit, eight
data bits and one or two stop bits. The second data format
for transmission consists of one start bit, nine data bits, and
one or two stop bits. Receiving formats differ from transmis-
sion only in that the Receiver always requires only one stop
bit in a data frame.
UART Wake-up Mode
The HPC46164 UART features a Wake-up Mode of opera-
tion. This mode of operation enables the HPC46164 to be
networked with other processors. Typically in such environ-
ments, the messages consist of addresses and actual data.
Addresses are specified by having the ninth bit in the data
frame set to 1. Data in the message is specified by having
the ninth bit in the data frame reset to 0.
The UART monitors the communication stream looking for
addresses. When the data word with the ninth bit set is
received, the UART signals the HPC46164 with an interrupt.
The processor then examines the content of the receiver
buffer to decide whether it has been addressed and whether
to accept subsequent data.
TL/DD/9682–28
FIGURE 26. UART Block Diagram
25
相關PDF資料
PDF描述
HPC46004VF20 High-Performance microController with A/D
HPC36104 High-Performance microController with A/D
HPC36164 High-Performance microController with A/D
HPC-DEV-ISE-E High-Performance microController with A/D
HPC-DEV-ISE4 High-Performance microController with A/D
相關代理商/技術參數
參數描述
HPCI-13S4LU 功能描述:模塊配件 ISAx7 PCIx4 PICMGx3 BACKPLANE AT/ATX PSU RoHS:否 制造商:Lantronix 產品: 用于:
HPCI-14S/ATX 功能描述:模塊配件 ISAx8 PCIx4 PICMGx2 BACKPLANE RoHS:否 制造商:Lantronix 產品: 用于:
HPCI-14S12U 功能描述:模塊配件 ISAx1 PCIx12 PICMGx2 BACKPLANE AT/ATX PSU RoHS:否 制造商:Lantronix 產品: 用于:
HPCI-14S7U 功能描述:模塊配件 ISAx4 PCIx7 PICMGx3 BACKPLANE AT/ATX PSU RoHS:否 制造商:Lantronix 產品: 用于:
HPCI-15S 功能描述:模塊配件 ISAx9 PCIx4 PICMGx2 BACKPLANE RoHS:否 制造商:Lantronix 產品: 用于:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*