- 您現在的位置：買賣IC網 > PDF目錄370620 > HM5225805BLTT-75 (ELPIDA MEMORY INC) 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM PDF資料下載
參數資料
| 型號： | HM5225805BLTT-75 |
| 廠商： | ELPIDA MEMORY INC |
| 元件分類： | DRAM |
| 英文描述： | 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| 中文描述： | 32M X 8 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 |
| 封裝： | 0.400 INCH, PLASTIC, TSOP2-54 |
| 文件頁數： | 40/63頁 |
| 文件大?。?/td> | 462K |
| 代理商： | HM5225805BLTT-75 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Data Sheet E0082H10
40
Refresh
Auto-refresh:
All the banks must be precharged before executing an auto-refresh command. Since the auto-
refresh command updates the internal counter every time it is executed and determines the banks and the
ROW addresses to be refreshed, external address specification is not required. The refresh cycle is 8192
cycles/64 ms. (8192 cycles are required to refresh all the ROW addresses.) The output buffer becomes High-
Z after auto-refresh start. In addition, since a precharge has been completed by an internal operation after the
auto-refresh, an additional precharge operation by the precharge command is not required.
Self-refresh:
After executing a self-refresh command, the self-refresh operation continues while CKE is held
Low. During self-refresh operation, all ROW addresses are refreshed by the internal refresh timer. A self-
refresh is terminated by a self-refresh exit command. Before and after self-refresh mode, execute auto-refresh
to all refresh addresses in or within 64 ms period on the condition (1) and (2) below.
(1) Enter self-refresh mode within 7.8 μs after either burst refresh or distributed refresh at equal interval to all
refresh addresses are completed.
(2) Start burst refresh or distributed refresh at equal interval to all refresh addresses within 7.8 μs after exiting
from self-refresh mode.
Others
Power-down mode:
The SDRAM enters power-down mode when CKE goes Low in the IDLE state. In
power down mode, power consumption is suppressed by deactivating the input initial circuit. Power down
mode continues while CKE is held Low. In addition, by setting CKE to High, the SDRAM exits from the
power down mode, and command input is enabled from the next clock. In this mode, internal refresh is not
performed.
Clock suspend mode:
By driving CKE to Low during a bank-active or read/write operation, the SDRAM
enters clock suspend mode. During clock suspend mode, external input signals are ignored and the internal
state is maintained. When CKE is driven High, the SDRAM terminates clock suspend mode, and command
input is enabled from the next clock. For details, refer to the "CKE Truth Table".
Power-up sequence:
The SDRAM should be goes on the following sequence with power up.
The CLK, CKE,
CS
, DQM, DQMU/DQML and DQ pins keep low till power stabilizes.
The CLK pin is stabilized within 100 μs after power stabilizes before the following initialization sequence.
The CKE and DQM, DQMU/DQML is driven to high between power stabilizes and the initialization
sequence.
This SDRAM has V
CC
clamp diodes for CLK, CKE,
CS
DQM, DQMU/DQML and DQ pins. If these pins go
high before power up, the large current flows from these pins to V
CC
through the diodes.
Initialization sequence:
When 200 μs or more has past after the above power-up sequence, all banks must be
precharged using the precharge command (PALL). After t
RP
delay, set 8 or more auto refresh commands
(REF). Set the mode register set command (MRS) to initialize the mode register. We recommend that by
keeping DQM, DQMU/DQML and CKE to High, the output buffer becomes High-Z during Initialization
sequence, to avoid DQ bus contention on memory system formed with a number of device.
相關PDF資料 |
PDF描述 |
|---|---|
| HM5225165B | 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225165B-75 | Ultra-High-Precision SOT23 Series Voltage Reference |
| HM5225165B-A6 | 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225165B-B6 | 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225165BLTT-75 | 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HM5225805BLTT-A6 | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225805BLTT-B6 | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225805BTT-75 | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225805BTT-A6 | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| HM5225805BTT-B6 | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
發布緊急采購，3分鐘左右您將得到回復。