- 您現在的位置：買賣IC網 > PDF目錄371814 > HI5634 (Intersil Corporation) High Performance Programmable Phase-Locked Loop for LCD Applications PDF資料下載
參數資料
| 型號： | HI5634 |
| 廠商： | Intersil Corporation |
| 英文描述： | High Performance Programmable Phase-Locked Loop for LCD Applications |
| 中文描述： | 高性能可編程鎖相環環路，用于LCD應用 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 131K |
| 代理商： | HI5634 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
6
Specific Layout Guidelines
1.
Digital Supply (VDDD)
- Bypass pin 1 (VDDD) to pin 2
(VSSD) with 4.7
μ
F and 0.1
μ
F capacitors, located as
close as possible to the pins. Traces must be maximally
wide and include multiple surface-etched vias to the ap-
propriate plane.
2.
External Loop Filter
-
Theuseofanexternalloopfilter
is strongly recommended in all designs.
Locate loop fil-
ter components as close to pins 8 and 9 (EXTFIL and EX-
TFILRET) as possible. Typical loop filter values are 6.8k
fortheseriesresistor,3300pFRF-typecapacitorforthese-
ries capacitor, and 150pF for the shunt capacitor.
3.
Analog PLL Supply (VDDA)
- Decouple pin 10 (VDDA)
with a series ferrite bead. Bypass the supply end of the
bead with 4.7
μ
F and 0.1
μ
F capacitors. Bypass pin 10 to
pin 11 (VSSA) with a 0.1
μ
F capacitor. Locate these com-
ponents as close as possible to the pins. Traces must be
maximally wide and have multiple surface-etched vias to
the power or ground planes.
4.
PECL Current Set Resistor
- Locate PECL current set
resistor as close as possible to pin 24 (IREF). Bypass pin
24 to ground with a 0.1
μ
F capacitor.
5.
PECL Outputs
- Implement these outputs as microstrip
transmission lines. The trace widths shown are for 75
characteristic impedance, presuming 0.067 in. between
layers. Locate the optional series “snubbing” resistors as
close as possible to the pins. If the termination resistors
are included on-board, locate them as close as possible
to the load and connect directly to the power and ground
planes (these termination resistors are omitted if the load
device implements them internally).
6.
Output Driver Supply (VDDQ)
- Bypass pin 18 (VDDQ)
to pin 19 (VSSQ) with 4.7
μ
F and 0.1
μ
F capacitors, locat-
ed as close as possible to the pins. Traces must be max-
imally wide and include multiple surface-etched vias to
the appropriate plane.
7.
SSTL_3 Outputs
- SSTL_3 outputs can be used like con-
ventional CMOS rail-to-rail logic or as a terminated trans-
mission line system at higher-output frequencies. With
terminated outputs, the considerations of item 5, “PECL
Outputs” apply. See JEDEC documents JESD8-A and
JESD8-8.
Power Supply Considerations
The HI5634 incorporates special internal power-on-reset
circuitry that requires no external reset signal connection.
The supply voltage (VDD) must remain within the
recommended operating conditions during normal operation.
To reset the HI5634, the supply voltage at the part must be
reduced below the threshold voltage (V
TH
) of the power-on-
reset circuit. The supply voltage must remain below that
threshold voltage such that board power conditioning
capacitors are drained and the proper reset state is latched.
The amount of time (t
D
) to hold the voltage in a reset state
varies with the design. However, a typical value of 10ms
should be sufficient.
SSTL_3 Outputs
Unterminated Outputs
In the HI5634, unterminated SSTL output pins display
exponential transitions similar to those of rectangular pulses
presented to RC loads. The 10-90% rise time is typically
1.6ns, and the corresponding fall time is typically 700ps. In
turn, this asymmetry contributes to duty cycle asymmetry at
higher output frequencies. In the absence of significant load
capacitance (which can further increase rise and fall time),
this asymmetry is the dominant factor determining high
frequency performance of these single-ended outputs.
Typically, no termination is required for the LOCK/REF,
FUNC, and CLK/2 outputs nor for CLK outputs up to
approximately 135MHz.
Terminated Outputs
SSTL_3 outputs are intended to terminate in low
impedances to reduce the effect of external circuit
capacitance. Use of transmission line techniques enables
use of longer traces between source and driver without
increasing ringing due to reflections. Where external
capacitance is minimal and substantial voltage swing is
required to meet LVTTL V
IH
and V
IL
requirements, the
intrinsic rise and fall times of HI5634 SSTL outputs are only
slightly improved by termination in a low impedance.
The HI5634 SSTL output source impedance is typically less
than 60
. Termination impedance of 100
reduces output
swing by less than 30% which is more than enough to drive
a single load of LVTTL inputs.
V
MIN
V
TH
= 1.8V
t
D
VDD
HI5634
SINGLE
LVTTL
LOAD
SSTL_3 OUTPUT
VDD
330
150
HI5634
相關PDF資料 |
PDF描述 |
|---|---|
| HI5634CB | High Performance Programmable Phase-Locked Loop for LCD Applications |
| HI5640 | 3.3V Dual 8-Bit， 40 MSPS A/D Converter with Internal Voltage Reference (3 pages) FN4657 |
| HI5640CN | Converter IC |
| HI5660EVAL1 | 8-Bit, 165/125/60MSPS, High Speed D/A Converter |
| HI5660IA | CONNECTOR ACCESSORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5634_00 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High Performance Programmable Phase-Locked Loop for LCD Applications |
| HI5634CB | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High Performance Programmable Phase-Locked Loop for LCD Applications |
| HI5640 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:3.3V Dual 8-Bit， 40 MSPS A/D Converter with Internal Voltage Reference (3 pages) FN4657 |
| HI5640CN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter IC |
| HI-565 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High Speed, Monolithic D/A Converter with Reference |
發布緊急采購，3分鐘左右您將得到回復。