- 您現在的位置：買賣IC網 > PDF目錄296101 > HGTP12N60C3_NL (FAIRCHILD SEMICONDUCTOR CORP) 24A,600V, UFS Series N-Channel IGBTs PDF資料下載
參數資料
| 型號： | HGTP12N60C3_NL |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | IGBT 晶體管 |
| 英文描述： | 24A,600V, UFS Series N-Channel IGBTs |
| 中文描述： | 24 A, 600 V, N-CHANNEL IGBT, TO-220AB |
| 文件頁數： | 6/7頁 |
| 文件大小： | 172K |
| 代理商： | HGTP12N60C3_NL |
2001 Fairchild Semiconductor Corporation
HGTP12N60C3, HGT1S12N60C3S Rev. B
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to
gate-insulation damage by the electrostatic discharge of
energy through the devices. When handling these devices,
care should be exercised to assure that the static charge built
in the handler’s body capacitance is not discharged through
the device. With proper handling and application procedures,
however, IGBTs are currently being extensively used in
production by numerous equipment manufacturers in military,
industrial and consumer applications, with virtually no damage
problems due to electrostatic discharge. IGBTs can be
handled safely if the following basic precautions are taken:
1. Prior to assembly into a circuit, all leads should be kept
shorted together either by the use of metal shorting
springs or by the insertion into conductive material such
as “ECCOSORBD
LD26” or equivalent.
2. When devices are removed by hand from their carriers,
the hand being used should be grounded by any suitable
means - for example, with a metallic wristband.
3. Tips of soldering irons should be grounded.
4. Devices should never be inserted into or removed from
circuits with power on.
5. Gate Voltage Rating - Never exceed the gate-voltage
rating of VGEM. Exceeding the rated VGE can result in
permanent damage to the oxide layer in the gate region.
6. Gate Termination - The gates of these devices are
essentially capacitors. Circuits that leave the gate open-
circuited or floating should be avoided. These conditions
can result in turn-on of the device due to voltage buildup
on the input capacitor due to leakage currents or pickup.
7. Gate Protection - These devices do not have an internal
monolithic zener diode from gate to emitter. If gate
protection is required an external zener is recommended.
Operating Frequency Information
Operating frequency information for a typical device
Figure 13) is presented as a guide for estimating device
performance for a specific application. Other typical
frequency vs collector current (ICE) plots are possible using
the information shown for a typical unit in Figures 4, 7, 8, 11
and 12. The operating frequency plot (Figure 13) of a typical
device shows fMAX1 or fMAX2 whichever is smaller at each
point. The information is based on measurements of a
typical device and is bounded by the maximum rated
junction temperature.
fMAX1 is defined by fMAX1 = 0.05/(tD(OFF)I+ tD(ON)I).
Deadtime (the denominator) has been arbitrarily held to 10%
of the on- state time for a 50% duty factor. Other definitions
are possible. tD(OFF)I and tD(ON)I are defined in Figure 19.
Device turn-off delay can establish an additional frequency
limiting condition for an application other than TJM. tD(OFF)I
is important when controlling output ripple under a lightly
loaded condition.
fMAX2 is defined by fMAX2 = (PD - PC)/(EOFF + EON). The
allowable dissipation (PD) is defined by PD = (TJM - TC)/RθJC.
The sum of device switching and conduction losses must not
exceed PD. A 50% duty factor was used (Figure 13) and the
conduction losses (PC) are approximated by
PC =(VCE xICE)/2.
EON and EOFF are defined in the switching waveforms
shown in Figure 19. EON is the integral of the instantaneous
power loss (ICE x VCE) during turn-on and EOFF is the
integral of the instantaneous power loss (ICE x VCE) during
turn-off. All tail losses are included in the calculation for
EOFF; i.e. the collector current equals zero (ICE = 0).
Test Circuit and Waveform
FIGURE 18. INDUCTIVE SWITCHING TEST CIRCUIT
FIGURE 19. SWITCHING TEST WAVEFORMS
RG = 25
L = 100
H
VDD = 480V
+
-
RHRP1560
tfI
td(OFF)I
trI
td(ON)I
10%
90%
10%
90%
VCE
ICE
VGE
EOFF
EON
HGTP12N60C3, HGT1S12N60C3S
相關PDF資料 |
PDF描述 |
|---|---|
| HGTP12N60C3D_NL | 24A, 600V, UFS Series N-Channel IGBT with Anti-Parallel Hyperfast Diodes |
| HGTP20N60A4_NL | 600V, SMPS Series N-Channel IGBTs |
| HGTP2N120CN_NL | 13A, 1200V, NPT Series N-Channel IGBT |
| HGTP3N60A4_NL | 600V, NPT Series N-Channel IGBT |
| HGTP3N60A4D_NL | 600V, SMPS Series N-Channel IGBT with Anti-Parallel Hyperfast Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HGTP12N60C3R | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HGTP12N60D1 | 制造商:Harris Corporation 功能描述: |
| HGTP14N0FVLR4600 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HGTP14N36G3VL | 功能描述:IGBT 晶體管 14a 380V Logic Level RoHS:否 制造商:Fairchild Semiconductor 配置: 集電極—發射極最大電壓 VCEO:650 V 集電極—射極飽和電壓:2.3 V 柵極/發射極最大電壓:20 V 在25 C的連續集電極電流:150 A 柵極—射極漏泄電流:400 nA 功率耗散:187 W 最大工作溫度: 封裝 / 箱體:TO-247 封裝:Tube |
| HGTP14N37G3VL | 功能描述:IGBT 晶體管 14A 370V N-Ch RoHS:否 制造商:Fairchild Semiconductor 配置: 集電極—發射極最大電壓 VCEO:650 V 集電極—射極飽和電壓:2.3 V 柵極/發射極最大電壓:20 V 在25 C的連續集電極電流:150 A 柵極—射極漏泄電流:400 nA 功率耗散:187 W 最大工作溫度: 封裝 / 箱體:TO-247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。