參數資料
型號： HFA3860IV96
廠商： HARRIS SEMICONDUCTOR
元件分類： 無繩電話/電話
英文描述： 11 Mbps Direct Sequence Spread Spectrum Baseband Processor
中文描述： TELECOM, CELLULAR, BASEBAND CIRCUIT, PQFP48
文件頁數： 14/40頁
文件大?。?/td> 250K
代理商： HFA3860IV96
4-14
compliance with IEEE 802.11.
Length Field (16 Bits) -
This field indicates the number of
microseconds it will take to transmit the payload data
(MPDU). The external controller will check the length field in
determining when it needs to de-assert the RX_PE.
CCITT - CRC 16 Field (16 Bits)-
This field includes the 16-
bit CCITT - CRC 16 calculation of the five header fields. This
value is compared with the CCITT - CRC 16 code calculated
at the receiver. The HFA3860 receiver will indicate a CCITT -
CRC 16 error via CR24 bit 2 and will lower MD_RDY if there
is an error.
The CRC or cyclic Redundancy Check is a CCITT CRC-16
FCS (frame check sequence). It is the ones compliment of
the remainder generated by the modulo 2 division of the
protected bits by the polynomial:
x
16
+ x
12
+ x
5
+ 1
The protected bits are processed in transmit order. All CRC
calculations are made prior to data scrambling. A shift
register with two taps is used for the calculation. It is preset
to all ones and then the protected fields are shifted through
the register. The output is then complemented and the
residual shifted out MSB first.
The following Configuration Registers (CR) are used to
program the preamble/header functions, more programming
details about these registers can be found in the Control
Registers section of this document:
CR 6
Defines the preamble length in symbols. The 802.11 protocol
requires a setting of 128d = 80h.
CR 15
- Defines the length of time that the demodulator
searches for the SFD before returning to acquisition.
CR 16.
The contents of this register define DBPSK modulation.
If CR 20 bits 1 and 0 are set to indicate DBPSK modulation
then the contents of this register are transmitted in the signal
field of the header.
CR 17.
The contents of this register define DQPSK modulation.
If CR 20 bits 1 and 0 are set to indicate DQPSK modulation
then the contents of this register are transmitted in the signal
field of the header.
CR 18.
The contents of this register define BMBOK modula-
tion. If CR 20 bits 1 and 0 are set to indicate BMBOK modula-
tion then the contents of this register are transmitted in the
signal field of the header.
CR 19.
The contents of this register define QMBOK modula-
tion. If CR 20 bits 1 and 0 are set to indicate QMBOK modula-
tion then the contents of this register are transmitted in the
signal field of the header.
CR 20.
The last two bits of the register indicate what modula-
tion is to be used for the data portion of the packet.
CR 21.
The value to be used in the Service field.
CR 22, 23.
Defines the value of the transmit data length field.
This value includes all symbols following the last header field
symbol and is in microseconds required to transmit the data at
the chosen data rate.
The packet consists of the preamble, header and MAC
protocol data unit (MPDU). The data is transmitted exactly as
received from the control processor. Some dummy bits will be
appended to the end of the packet to insure an orderly
shutdown of the transmitter. This prevents spectrum splatter.
At the end of a packet, the external controller is expected to
de-assert the TX_PE line to shut the transmitter down.
Scrambler and Data Encoder Description
The modulator has a data scrambler that implements the
scrambling algorithm specified in the IEEE 802.11 standard.
This scrambler is used for the preamble, header, and data in
all modes. The data scrambler is a self synchronizing circuit.
It consist of a 7-bit shift register with feedback from specified
taps of the register, as programmed through configuration
register CR 7. Both transmitter and receiver use the same
scrambling algorithm. The scrambler can be disabled by
setting the taps to 0.
Scrambling is done by a polynomial division using a
prescribed polynomial as shown in Figure 10. A shift register
holds the last quotient and the output is the exclusive-or of
the data and the sum of taps in the shift register. The taps
are programmable. The transmit scrambler seed is Hex 6C
and the taps are set with CR 7.
For the 1 Mbps DBPSK data rates and for the header in all
rates, the data coder implements the desired DBPSK coding by
PREAMBLE (SYNC)
128 BITS
SFD
16 BITS
SIGNAL FIELD
8 BITS
SERVICE FIELD
8 BITS
LENGTH FIELD
16 BITS
CRC16
16 BITS
HEADER
PREAMBLE
FIGURE 9. 802.11 PREAMBLE/HEADER
FIGURE 10. SCRAMBLING PROCESS
Z
-1
Z
-2
Z
-3
Z
-4
Z
-5
Z
-6
Z
-7
XOR
XOR
SERIAL DATA
INPUT
SERIAL DATA
OUTPUT
HFA3860
相關PDF資料
PDF描述
HFA3861A Direct Sequence Spread Spectrum Baseband Processor(直接序列擴頻基帶處理器)
HFA3861B Direct Sequence Spread Spectrum Baseband Processor(直接序列擴譜基帶處理器)
HFA3861 Direct Sequence Spread Spectrum (DSSS) baseband processor(直接序列擴頻基帶處理器)
HFA3861IV Direct Sequence Spread Spectrum Baseband Processor
HFA3861IV96 Direct Sequence Spread Spectrum Baseband Processor
相關代理商/技術參數
參數描述
HFA3861 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband Processor
HFA3861A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband Processo
HFA3861AIN 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband Processo
HFA3861AIN96 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband Processo
HFA3861B 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*