參數資料
型號： HD4074629
廠商： Hitachi,Ltd.
英文描述： AS Microcomputer Incorporating a DTMF Generator Circuit(微計算機帶雙音多頻發生器電路)
中文描述： 由于微機安裝有雙音多頻發電機斷路器（微計算機帶雙音多頻發生器電路）
文件頁數： 18/155頁
文件大?。?/td> 549K
代理商： HD4074629
HD404629R Series
18
SPX Register (SPX) and SPY Register (SPY):
The SPX and SPY registers are 4-bit registers used to
supplement the X and Y registers.
Carry Flag (CA):
CA is a 1-bit flag that stores ALU overflow generated by an arithmetic operation. CA is
set to 1 when an overflow is generated, and is cleared to 0 after operations in which no overflow occurred.
CA is also affected by the carry set/carry clear instructions (SEC and REC), and by the rotate with carry
instructions (ROTL and ROTR).
During interrupt handling, CA is saved on the stack, and is restored from the stack by the RTNI instruction.
Status Flag (ST):
ST is a 1-bit flag that stores the results of arithmetic instructions, compare instructions,
and bit test instructions, and is used as the branch condition for the BR, BRL, CAL, and CALL conditional
branch instructions.
The contents of the ST flag are held until the next arithmetic, compare, bit test, or conditional branch
instruction is executed. After the execution of a conditional branch instruction, the value of ST is set to 1
without regard to the condition.
During interrupt handling, ST is saved on the stack, and is restored from the stack by the RTNI instruction.
Program Counter (PC):
The PC is a 14-bit counter that indicates the ROM address of the next instruction
the CPU will execute.
Stack Pointer (SP):
The SP is a 10-bit register that indicates the RAM address of the next stack frame in
the stack area.
The SP is initialized to $3FF by a reset. The SP is decremented by 4 by a subroutine call or by interrupt
handling, and is incremented by 4 when the saved data has been restored by a return instruction.
The upper 4 bits of the SP are fixed at 1111; the maximum number of stack levels is thus 16.
In addition to the reset method described above, the SP can also be initialized to $3FF by clearing the reset
stack pointer (RSP) in the interrupt control bits area with a RAM bit manipulation instruction, i.e., REM or
REMD.
Reset
The MCU is reset by inputting a high-level voltage to the RESET pin. At power-on or when stop mode is
cancelled, RESET must be high for at least one t
RC
to enable the oscillator to stabilize. During operation,
RESET must be high for at least two instruction cycles.
Initial values after MCU reset are listed in table 1.
相關PDF資料
PDF描述
HD404629R AS Microcomputer Incorporating a DTMF Generator Circuit(微計算機帶雙音多頻發生器電路)
HD404638R 4-Bit Single-Chip Microcomputer(4位單片微計算機)
HD40A4638R 4-Bit Single-Chip Microcomputer(4位單片微計算機)
HD40A4639R 4-Bit Single-Chip Microcomputer(4位單片微計算機)
HD404639R 4-Bit Single-Chip Microcomputer(4位單片微計算機)
相關代理商/技術參數
參數描述
HD4074629F 制造商:Renesas Electronics Corporation 功能描述:
HD4074629FS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
HD4074629H 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
HD4074629TF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
HD4074654 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*