- 您現在的位置：買賣IC網 > PDF目錄370450 > HCPL-0710 40 ns Propagation Delay,CMOS Optocoupler(40 ns 傳播延遲，CMOS耦合器) PDF資料下載
參數資料
| 型號： | HCPL-0710 |
| 英文描述： | 40 ns Propagation Delay,CMOS Optocoupler(40 ns 傳播延遲，CMOS耦合器) |
| 中文描述： | 40納秒的傳播延遲，光耦的CMOS（40納秒的傳播延遲，耦合器的CMOS） |
| 文件頁數： | 13/16頁 |
| 文件大小： | 304K |
| 代理商： | HCPL-0710 |
13
Figure 20. Isolated Node with Transceiver Powered by the Network.
Isolated Node with
Transceiver Powered by the
Network
Figure 20 shows a node powered
by both the network and another
source. In this case, the trans-
ceiver and isolated (network) side
of the two optocouplers are
powered by the network. The rest
of the node is powered by the AC
line which is very beneficial when
an application requires a
significant amount of power. This
method is also desirable as it does
not heavily load the network.
More importantly, the unique
“dual-inverting” design of the
HCPL-x710 ensure the network
will not “l(fā)ock-up” if either AC line
power to the node is lost or the
node powered-off. Specifically,
when input power (V
DD1
) to the
HCPL-x710 located in the
transmit path is eliminated, a
RECESSIVE bus state is ensured
as the HCPL-x710 output voltage
(V
O
) go HIGH.
*Bus V+ Sensing
It is suggested that the Bus V+
sense block shown in Figure 20
be implemented. A locally
powered node with an un-
powered isolated Physical Layer
will accumulate errors and
become bus-off if it attempts to
transmit. The Bus V+ sense
signal would be used to change
the BOI attribute of the DeviceNet
Object to the “auto-reset” (01)
value. Refer to Volume 1, Section
5.5.3. This would cause the node
to continually reset until bus
power was detected. Once power
was detected, the BOI attribute
would be returned to the “hold in
bus-off” (00) value. The BOI
attribute should not be left in the
“auto-reset” (01) value since this
defeats the jabber protection
capability of the CAN error
confinement. Any inexpensive low
frequency optical isolator can be
used to implement this feature.
NODE/APP SPECIFIC
uP/CAN
HCPL
x710
HCPL
x710
TRANSCEIVER
NON ISO
5 V
REG.
NETWORK
POWER
SUPPLY
V+ (SIGNAL)
V– (SIGNAL)
V+ (POWER)
V– (POWER)
GALVANIC
ISOLATION
BOUNDARY
AC LINE
DRAIN/SHIELD
SIGNAL
POWER
*HCPL
x710
* OPTIONAL FOR BUS V + SENSE
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-0720 | 40 ns Propagation Delay,CMOS Optocoupler(40 ns 傳播延遲，CMOS光耦合器) |
| HCPL-0721 | 40 ns Propagation Delay,CMOS Optocoupler(40 ns 傳播延遲，CMOS光耦合器) |
| HCPL-0731 | Dual Channel Low Input Current, High Gain Optocouplers(雙通道，低輸入電流，高增益光耦器) |
| HCPL-2730 | Dual Channel Low Input Current, High Gain Optocouplers(雙通道，低輸入電流，高增益光耦器) |
| HCPL-2731 | Dual Channel Low Input Current, High Gain Optocouplers(雙通道，低輸入電流，高增益光耦器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL-0710#060 | 功能描述:高速光耦合器 1Ch 150mA 600mW RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL-0710#500 | 功能描述:高速光耦合器 1Ch 150mA 600mW RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL0710#560 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FET-OUTPUT OPTOCOUPLER |
| HCPL-0710#560 | 功能描述:高速光耦合器 1Ch 150mA 600mW RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL-0710-000E | 功能描述:高速光耦合器 1Ch 150mA 600mW RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。