參數資料
型號： HCD40C4084
廠商： Hitachi,Ltd.
英文描述： Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
中文描述： 低電壓如同在微機芯片的A / D轉換器（帶片上的A / D轉換器的低壓微計算機）
文件頁數： 85/162頁
文件大?。?/td> 482K
代理商： HCD40C4084
HD404374/HD404384/HD404389/HD404082/HD404084 Series
85
Timer C Operation
Free-running/reload timer:
Free-running/reload timer operation, the input clock source, and the prescaler division ratio are selected
by means of timer mode register C1 (TMC1).
Timer C is initialized to the value written to timer write register C (TWCL, TWCU) by software, and
counts up by 1 each time the input clock is input. When the input clock is input after the timer C value
reaches $FF, overflow output is generated. Timer C is then set to the value in timer write register C
(TWCL, TWCU) if the reload timer function is selected, or to $00 if the free-running timer function is
selected, and starts counting up again.
Overflow output sets the timer C interrupt request flag (IFTC). This flag is reset by the program or by
an MCU reset.
For details, see figure 3, Interrupt Control Bit and Register Flag Area Configuration, and table 1, Initial
Values after MCU Reset.
16-bit timer operation:
When timer B overflow flag is selected as the clock source, timer C can be used as a 16-bit timer that
counts the timer B clock source pulses. In this case, since the timer B and timer C free-running/reload
settings are independent, the settings should be made to suit the purpose.
Watchdog timer operation:
By using the timer C overflow output, timer C can be used as a watchdog timer for detecting program
runaway. The watchdog timer is enabled when the watchdog on flag (WDON) is set to 1, and generates
an MCU reset when timer C overflows. Usually, timer C initialization is performed by the program
before the timer C value reaches $FF, so controlling program runaway.
Timer output operation:
With timer C, the R2
0
/TOC pin is designated as the TOC pin by setting bit 0 of port mode register 3
(PMR3) to 1, and toggle waveform output or PWM waveform output can be selected by timer mode
register C2 (TMC2).
Toggle output
The operation is similar to that for timer B toggle output.
PWM output
The operation is similar to that for timer B PWM output.
Module standby:
The operation is similar to that for timer B module standby.
相關PDF資料
PDF描述
HCD40C4344R 4-bit HMCS400-series microcomputer(4位單片微計算機)
HCD44780UBxx 320 x 240 pixel format, CFL backlight available with power harness
HCD44780UA00 320 x 240 pixel format, CFL backlight available with power harness
HCD44780UA02 320 x 240 pixel format, CFL backlight available with power harness
HCD61202U Dot Matrix Liquid Crystal GraphicDisplay Column Driver
相關代理商/技術參數
參數描述
HCD40C4344R 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit microcomputers
HCD44780UA00 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD44780UA02 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD44780UBXX 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD48-3318-75 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC to DC Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*