參數資料
型號： HCD40C4084
廠商： Hitachi,Ltd.
英文描述： Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
中文描述： 低電壓如同在微機芯片的A / D轉換器（帶片上的A / D轉換器的低壓微計算機）
文件頁數： 32/162頁
文件大?。?/td> 482K
代理商： HCD40C4084
HD404374/HD404384/HD404389/HD404082/HD404084 Series
32
W register (W), X register (X) and Y register (Y):
The W register is a 2-bit register, and the X and Y registers are 4-bit registers, used for RAM register
indirect addressing. The Y register is also used for D port addressing.
SPX register (SPX) and SPY register (SPY):
The SPX and SPY registers are 4-bit registers used as X register and Y register auxiliary registers,
respectively.
Carry flag (CA):
This flag holds ALU overflow when an arithmetic/logic instruction is executed. It is also affected by the
SEC, REC, ROTL, and ROTR instructions. The contents of the carry flag are saved to the stack when
interrupt handling is performed, and are restored from the stack by the RTNI instruction (but are not
affected by the RTN instruction).
Status flag (ST):
This flag holds ALU overflow when an arithmetic/logic or compare instruction is executed, and the result
of an ALU non-zero or bit test instruction. It is used as the branch condition for the BR, BRL, CAL, and
CALL instructions. The status flag is a latch-type flag, and does not change until the next arithmetic/logic,
compare, or bit test instruction is executed. After a BR, BRL, CAL, or CALL instruction, the status flag is
set to 1 regardless of whether the instruction is executed or skipped. The contents of the status flag are
saved to the stack when interrupt handling is performed, and are restored from the stack by the RTNI
instruction (but are not affected by the RTN instruction).
Program counter (PC):
This is a 14-bit binary counter that holds ROM address information.
Stack pointer (SP):
The stack pointer is a 10-bit register that holds the address of the next save space in the stack area. The
stack pointer is initialized to $3FF by an MCU reset. The stack pointer is decremented by 4 each time data
is saved, and incremented by 4 each time data is restored. The upper 4 bits of the stack pointer are fixed at
1111, so that a maximum of 16 stack levels can be used.
There are two ways in which the stack pointer is initialized to $3FF: by an MCU reset as mentioned above,
or by resetting the RSP bit with the REM or REMD instruction.
Reset
An MCU reset is performed by driving the
RESET
pin low. At power-on, and when subactive mode,
watch mode, or stop mode is cleared,
RESET
should be input for at least tRC to provide the oscillation
settling time for the oscillator.In other cases, the MCU is reset by inputting
RESET
for at least two
instruction cycles.
Table 1 shows the areas initialized by an MCU reset, and their initial values.
相關PDF資料
PDF描述
HCD40C4344R 4-bit HMCS400-series microcomputer(4位單片微計算機)
HCD44780UBxx 320 x 240 pixel format, CFL backlight available with power harness
HCD44780UA00 320 x 240 pixel format, CFL backlight available with power harness
HCD44780UA02 320 x 240 pixel format, CFL backlight available with power harness
HCD61202U Dot Matrix Liquid Crystal GraphicDisplay Column Driver
相關代理商/技術參數
參數描述
HCD40C4344R 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit microcomputers
HCD44780UA00 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD44780UA02 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD44780UBXX 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD48-3318-75 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC to DC Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*